[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [Question] gpsd, ntrip & C94-M8P (u-Blox)
From: |
Gary E. Miller |
Subject: |
Re: [Question] gpsd, ntrip & C94-M8P (u-Blox) |
Date: |
Fri, 15 May 2020 10:00:45 -0700 |
Yo Florian!
You have reached my loop count limit. you say, I say, you say, I say,
you say, with no new info.
I'll skip this thread until there is new info.
On Fri, 15 May 2020 11:21:16 +0200
Florian Kiera <address@hidden> wrote:
> Hey Gary!
>
> Am 14.05.20 um 19:07 schrieb Gary E. Miller:
> > Yo Florian!
> >
> > On Thu, 14 May 2020 09:27:33 +0200
> > Florian Kiera <address@hidden> wrote:
> >
> >
> >>>> RTCM3 messages have been turned off and protocol out has been
> >>>> modified, as well as the dynModel
> >>> Yes, why/how did you do that?
> >> Ubxtool -p STATUS -p CONFIG -P 20.30
> > That reads, not writes. So not possible that turned off anything.
> Obviously it does write over the protocol out (UBX-CFG-PRT). I will
> send another console output. (attachment) It even proofs that ubxtool
> got 2 different config outputs ("although its only pulling").
> I cannot tell (simply don't know) what else could cause it. All I am
> certain of AND which I can proof is that ubxtool changed the protocol
> out from RTCM3 to UBX (check UBX-CFG-PRT).
> Sadly (which is actually good) dynModel didn't changed here.
> >>> I can't comment on messes you make without seeing how you did it.
> >>>
> >> Just ran "ubxtool -p STATUS -p CONFIG -P 20.30"... Since its hard
> >> to believe I will send just a quick summary of my console log.
> > Summaries are not useful. My mind reading and remote devination is
> > not strong enough. Full output, or do not bother.
>
> I don't know what you are up to here. I sent the console log of all
> what I did. Thats what made me believe ubxtool did not what it
> supposed to do there (ubxtool_does_something.txt).
>
> ubxtool aside and thinking of dynModel and RTCM3 messages beeing
> given out back to my actual question:
> My base sends RTCM3 messages and gpsd on the rover end is receiving
> them and provides them to my M8P (rover side). How is it not changing
> to RTK Float/Fix but to DGPS if all that is needed for RTK status are
> RTCM3 messages?
>
> Regards Florian
RGDS
GARY
---------------------------------------------------------------------------
Gary E. Miller Rellim 109 NW Wilmington Ave., Suite E, Bend, OR 97703
address@hidden Tel:+1 541 382 8588
Veritas liberabit vos. -- Quid est veritas?
"If you can't measure it, you can't improve it." - Lord Kelvin
pgpcSOkSjTdUO.pgp
Description: OpenPGP digital signature
- Re: [Question] gpsd, ntrip & C94-M8P (u-Blox), (continued)
- Re: [Question] gpsd, ntrip & C94-M8P (u-Blox), Florian Kiera, 2020/05/11
- Re: [Question] gpsd, ntrip & C94-M8P (u-Blox), Greg Troxel, 2020/05/11
- Re: [Question] gpsd, ntrip & C94-M8P (u-Blox), Gary E. Miller, 2020/05/11
- Re: [Question] gpsd, ntrip & C94-M8P (u-Blox), Florian Kiera, 2020/05/12
- Re: [Question] gpsd, ntrip & C94-M8P (u-Blox), Gary E. Miller, 2020/05/12
- Re: [Question] gpsd, ntrip & C94-M8P (u-Blox), Florian Kiera, 2020/05/13
- Re: [Question] gpsd, ntrip & C94-M8P (u-Blox), Gary E. Miller, 2020/05/13
- Re: [Question] gpsd, ntrip & C94-M8P (u-Blox), Florian Kiera, 2020/05/14
- Re: [Question] gpsd, ntrip & C94-M8P (u-Blox), Gary E. Miller, 2020/05/14
- Re: [Question] gpsd, ntrip & C94-M8P (u-Blox), Florian Kiera, 2020/05/15
- Re: [Question] gpsd, ntrip & C94-M8P (u-Blox),
Gary E. Miller <=