paparazzi-devel
[Top][All Lists]
Advanced

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Paparazzi-devel] paparazzi with 2.4GHz


From: evan igor
Subject: Re: [Paparazzi-devel] paparazzi with 2.4GHz
Date: Fri, 14 Mar 2014 12:59:29 +0200

Hi Felix,

i'm following the bind procedure in the wiki bu no flashing while i'm connecting On the connector ANALOG1 have a wire between the GND and ADC1 pin.

i must connect the bind plug to the receiver for flashing the receiver.   Is that correct or not?



On Fri, Mar 14, 2014 at 1:14 AM, Felix Ruess <address@hidden> wrote:
It has no influence whatsoever which radio xml file you choose if you are using the spektrum subsystem.
Currently you still have to specify one in order to satisfy the build system, even if it is not used...

Just follow the steps to bind your receiver...


On Thu, Mar 13, 2014 at 11:02 PM, evan igor <address@hidden> wrote:
so what is the wrong thing i did for setting and does the radio.xml has effect with transmitter.
and how could i get these parameters for my transmitter


On Thu, Mar 13, 2014 at 9:35 PM, Felix Ruess <address@hidden> wrote:
This comment was misleading, corrected it...


On Thu, Mar 13, 2014 at 2:51 PM, evan igor <address@hidden> wrote:
and what is this CAUTION! This is only used for PPM transmitters so it does not apply to DSM/DSM2/FASST/FHSS or other 2.4Ghz radios.  in http://wiki.paparazziuav.org/wiki/Radio_Control
mean as i can use the 2.4 Ghz

sorry for any interrupts and thanks for help in advance :)


On Thu, Mar 13, 2014 at 3:34 PM, evan igor <address@hidden> wrote:
Hi all;
i tried the binding sequence, one question i connected the bind cable to the receiver so i connect between GND and signal pin as well as connecting GND with ADC1 pin in ANALOGL1.  or i shouldn't connect the binding cable to the receiver and only connect  GND with ADC1 pin in ANALOGL1.



On Thu, Mar 13, 2014 at 3:02 PM, Felix Ruess <address@hidden> wrote:


On Thu, Mar 13, 2014 at 1:37 PM, evan igor <address@hidden> wrote:
Hi,

the problem i face that i have orange receiver this one

and i have also transmitter spektrum dx5e
but i tried to connect them with paparazzi liza/m and no signal while i use this radio.xml   i attached


On Thu, Mar 13, 2014 at 2:07 PM, Chris <address@hidden> wrote:
of course as long as either you have a PPM signal available from the receiver like
some Frsky ones, Spectrum receivers also work afaik
This signal is often called combined PPM (cppm) and other names as it is essentially a wavetrain containing the pulse width of all servos.
All LRS type (long range system) receivers have a ppm output as nearly all autopilots need that signal.
Chris


On 03/13/2014 12:47 PM, evan igor wrote:
Hi,
does paparazzi wok with 2.4Ghz transmitter?


as this 

CAUTION! This is only used for PPM transmitters so it does not apply to DSM/DSM2/FASST/FHSS or other 2.4Ghz radios. 



_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel


_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel



_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel



_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel




_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel



_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel



_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel



_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel



reply via email to

[Prev in Thread] Current Thread [Next in Thread]