[Top][All Lists]
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: Features for a new release. (was Re: [Denemo-devel] Midi output faul
From: |
Richard Shann |
Subject: |
Re: Features for a new release. (was Re: [Denemo-devel] Midi output faulty for whole measure rests in 4/2 time) |
Date: |
Wed, 29 Oct 2008 15:52:34 +0000 |
On Wed, 2008-10-29 at 08:11 -0500, Jeremiah Benham wrote:
> > >
> > > importmidi breaking voices into other staffs
> > (ok - I don't know what this is about, I guess because I have never
> used
> > importmidi in earnest)
>
> Where you at one time trying to get a midi controller or usb midi
> connector for your midi controller? Have you given up on that idea
> since
> you have the pitch detection working better for you?
It did slip down the priority list as a result of getting the pre-amp.
Then it went up again as I discovered the hum was getting in before the
pre-amp (it's rather erratic). Then it went down again as I found that
if I powered the small Yamaha keyboard via batteries it solved the mains
hum problem (naturally).
However, I have been tempted by the local supermarket offering a 61-note
Yamaha keyboard at a low price - I tend to run out of notes on the small
keyboard I have been using. But it doesn't have a USB output, only midi
connector, and so I started looking for those, only to find that they
are much more expensive. Which I can't really understand, as I see midi
to USB conversion cables sold for next to nothing - I don't know what
these really do, let alone whether Alsa &c support them... As far as I
can make out, there does seem to be some usb/midi standard that allows
people to sell usb devices (such as midi controller keyboards) with no
software drivers which Linux will support. But whether there is a a
simple cable that would take the midi output of my small Yamaha keyboard
and plug it into the USB port on the computer I can't figure out. The
people selling the cables don't give any details about what they do.
Richard
- [Denemo-devel] Midi output faulty for whole measure rests in 4/2 time, Richard Shann, 2008/10/28
- Re: [Denemo-devel] Midi output faulty for whole measure rests in 4/2 time, Jeremiah Benham, 2008/10/28
- Re: [Denemo-devel] Midi output faulty for whole measure rests in 4/2 time, Richard Shann, 2008/10/28
- Re: [Denemo-devel] Midi output faulty for whole measure rests in 4/2 time, Jeremiah Benham, 2008/10/28
- Features for a new release. (was Re: [Denemo-devel] Midi output faulty for whole measure rests in 4/2 time), Richard Shann, 2008/10/28
- Re: Features for a new release. (was Re: [Denemo-devel] Midi output faulty for whole measure rests in 4/2 time), Nils Gey, 2008/10/28
- Re: Features for a new release. (was Re: [Denemo-devel] Midi output faulty for whole measure rests in 4/2 time), Jeremiah Benham, 2008/10/29
- Re: Features for a new release. (was Re: [Denemo-devel] Midi output faulty for whole measure rests in 4/2 time),
Richard Shann <=
- Re: Features for a new release. (was Re: [Denemo-devel] Midi output faulty for whole measure rests in 4/2 time), Benoit Rouits, 2008/10/29
- Re: Features for a new release. (was Re: [Denemo-devel] Midi output faulty for whole measure rests in 4/2 time), Richard Shann, 2008/10/30
- Re: Features for a new release. (was Re: [Denemo-devel] Midi output faulty for whole measure rests in 4/2 time), Jeremiah Benham, 2008/10/30
- Re: Features for a new release. (was Re: [Denemo-devel] Midi output faulty for whole measure rests in 4/2 time), Jeremiah Benham, 2008/10/30
- Re: Features for a new release. (was Re: [Denemo-devel] Midi output faulty for whole measure rests in 4/2 time), Richard Shann, 2008/10/30
- Re: Features for a new release. (was Re: [Denemo-devel] Midi output faulty for whole measure rests in 4/2 time), Jeremiah Benham, 2008/10/30
- Re: Features for a new release. (was Re: [Denemo-devel] Midi output faulty for whole measure rests in 4/2 time), Richard Shann, 2008/10/31
- Re: Features for a new release. (was Re: [Denemo-devel] Midi output faulty for whole measure rests in 4/2 time), Richard Shann, 2008/10/29
- Re: Features for a new release. (was Re: [Denemo-devel] Midi output faulty for whole measure rests in 4/2 time), Jeremiah Benham, 2008/10/30
- Re: Features for a new release. (was Re: [Denemo-devel] Midi output faulty for whole measure rests in 4/2 time), Richard Shann, 2008/10/30