Re: [Paparazzi-devel] can't get any response from lisa/m even telemetry

[Luis Carlos]

connect your lisa board directly to ftdi and your pc..and test your connecttion to the pc...

Luis Carlos

El 12/02/2014 13:47, "evan igor" <address@hidden> escribió:

Hi,

yes and the 3dr has usb ready connection.

On Wed, Feb 12, 2014 at 6:23 PM, Luis Carlos <address@hidden> wrote:

you have a ftdi cable??

Luis Carlos

El 12/02/2014 12:41, "evan igor" <address@hidden> escribió:

i tested the telemetry when connecting power to lisa/m while the 3dr connected and i opened serial port connection xctu and there were adata transferred moreover i tested the 3dr with ardupilot and it was working correctly.

so there are a data from paparazzi but it may be no connection between CGS and the modem.

how could i check the connection with paparazzi only through the CGS?

On Wed, Feb 12, 2014 at 5:01 PM, Luis Carlos <address@hidden> wrote:

you have a solid green led in your's modem? maybe you test the telemetry port directly trought ftdi cable...if you have one ftdi...
Regards

Luis Carlos

El 12/02/2014 11:03, "evan igor" <address@hidden> escribió:

i'll do that as soon as i'll back home but what about the telemetry?

On Wed, Feb 12, 2014 at 3:25 PM, Luis Carlos <address@hidden> wrote:

for power the servos trought v in you need to short jp1 pads in the lisa board...please check the wiki instrucctions

Luis Carlos

El 12/02/2014 10:13, "Luis Carlos" <address@hidden> escribió:

hi evan...it's possible to you upload a picture of your's connection? You power the servo rail connection?
Regards

Luis Carlos

El 12/02/2014 07:24, "evan igor" <address@hidden> escribió:

Hi everyone;

i setup ubuntu 12.04 and reupload firmware to the lisa/m .

1- now i connect v_in to 5 volt of speed controller and GND to GND of speed controller.

2- connect the GPS neo_6m to the UART 3.

3- connect spectrum receiver to UART1/5.

4 connect 3dr to UART2 after disabling its mavlink mode to raw data.

connect a servo as test to one of the output of liza/m and after making binding while GND the ADC1 in ANALOG1.

upload firmware to the liza/m from the CGS for the quadrotor_lisa/m example.

 then connecting a servo for testing but there is no telemetry , no response for servo.

what should i check.

but no response in the servo even any power.

thanks and hope for help.

_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel

_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel

_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel

_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel

_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel

_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel

_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel