Re: [Paparazzi-devel] Baro MS5611-01BA01

[Árni Þorvaldsson]

Thanks alot, only thing I am now thinking about is do I need to wire CSB pin to 
both GND and VDD?

regards Arni
________________________________
Frá: address@hidden address@hidden fyrir hönd Eduardo lavratti address@hidden
Sent: 5. febrúar 2013 21:06
To: Paparazzi developer forum
Efni: Re: [Paparazzi-devel] Baro MS5611-01BA01

How you connected the sensor to ppz hardware ? The sensor come you breakout 
board ?
look at PS pin as Arni say and look as CSB pin too.

CSB define the i2c address.


> From: address@hidden
> Date: Wed, 6 Feb 2013 09:45:50 +1300
> To: address@hidden
> Subject: Re: [Paparazzi-devel] Baro MS5611-01BA01
>
> Hi Arni,
>
> The datasheet says you need to pull the protocol select pin PS high to put it 
> into I2C mode rather than SPI. Have you done this? You didn't mention it in 
> your wiring description.
>
> Regards,
>
> Avinash.
>
> ______________________
> Avinash Rao
> +(64) 27 429 1159
> _______________________
>
>
> On 6/02/2013, at 9:34, Árni Þorvaldsson <address@hidden> wrote:
>
> > Hi sorry my mistake, the version is Paparazzi version 
> > v4.9_devel-419-gc2d60af
> > I got the sensors from http://sander-electronic.de/be00067.html
> >
> > How do I check if the adress is correct?
> >
> > Regards Arni
> > ________________________________
> > Frá: address@hidden address@hidden fyrir hönd Eduardo lavratti 
> > address@hidden
> > Sent: 5. febrúar 2013 20:19
> > To: Paparazzi developer forum
> > Efni: Re: [Paparazzi-devel] Baro MS5611-01BA01
> >
> > first of all, where you get your sensor ?
> > The address used are correct ?
> >
> > second, i think you pass the version of GIT program not the version of REPO
> >
> >> From: address@hidden
> >> To: address@hidden
> >> Date: Tue, 5 Feb 2013 18:06:44 +0000
> >> Subject: [Paparazzi-devel] Baro MS5611-01BA01
> >>
> >> Hi
> >> I am still trying to get messages from my baro without any luck.
> >> My git version 1.7.9.5
> >> I am only trying to get the messages from the sensor displayed in messages 
> >> tool (not use it during the flight). I don't get any errors, just no 
> >> message from the sensor.
> >> my wiring is as follow:
> >> vdd-5v
> >> gnd-gnd
> >> SDI/SDA-SDA
> >> SCLK-SCL
> >>
> >> If anyone has an idea what to try to fix this, please tell me:)
> >>
> >> Here is my firmware part:
> >>
> >> <!DOCTYPE airframe SYSTEM "airframe.dtd">
> >>
> >> <airframe name="Funjet Tiny 2.11">
> >>
> >> <firmware name="fixedwing">
> >> <define name="SENSOR_SYNC_SEND"/>
> >> <define name="USE_AIRSPEED"/>
> >> <target name="sim" board="pc"/>
> >>
> >> <target name="ap" board="tiny_2.11">
> >> <define name="USE_I2C0"/>
> >> <define name="USE_I2C1"/>
> >> </target>
> >>
> >> <subsystem name="radio_control" type="ppm"/>
> >> <subsystem name="joystick"/>
> >>
> >> <!-- Communication -->
> >> <subsystem name="telemetry" type="transparent"/>
> >> <subsystem name="imu" type="ppzuav"/>
> >>
> >>
> >> <!-- Actuators are automatically chosen according to board-->
> >> <subsystem name="control"/>
> >> <!-- Sensors -->
> >> <subsystem name="ahrs" type="float_dcm"/>
> >> <subsystem name="gps" type="ublox"/>
> >> <subsystem name="ins" type="alt_float"/>
> >> <subsystem name="navigation"/>
> >>
> >>
> >> </firmware>
> >>
> >> <modules>
> >> <load name="infrared_adc.xml"/>
> >> <load name="baro_ms5611_i2c.xml"/>
> >> <load name="airspeed_ets.xml"/>
> >> </modules>
> >>
> >> <firmware name="setup">
> >> <target name="tunnel" board="tiny_2.11"/>
> >> <target name="setup_actuators" board="tiny_2.11"/>
> >> </firmware>
> >>
> >>
> >> regards Arni
> >>
> >> _______________________________________________
> >> Paparazzi-devel mailing list
> >> address@hidden
> >> https://lists.nongnu.org/mailman/listinfo/paparazzi-devel
> >
> > _______________________________________________
> > Paparazzi-devel mailing list
> > address@hidden
> > https://lists.nongnu.org/mailman/listinfo/paparazzi-devel
>
> _______________________________________________
> Paparazzi-devel mailing list
> address@hidden
> https://lists.nongnu.org/mailman/listinfo/paparazzi-devel