Re: Grub install fails on single boot Mint 17, 3TB RAID1, GPT & EFI

[Andrei Borzenkov]

В Thu, 1 Jan 2015 14:43:54 -0800 (PST)
address@hidden пишет:

> Greetings -
> 
> I am trying to install Linux Mint 17.1 onto a new Dell Precision and am 
> getting a grub-install failed error from the installer. This is a new 
> single-boot UEFI system with 2 blank 3 TB drives. Specifically the error is:
> 
> Running grub-install /dev/md127
> Unable to install GRUB in /dev/md127
> Executing ‘grub-install /dev/md127’ failed
> This is a fatal error
> 
> Since this is the only error information that I have, I am assuming that it 
> could be a result of the raid and partitioning setup that the installer balks 
> at when installing Grub2. So I will start by clearly stating what my 
> objective is, then my disk setup.

You should look at distribution specific log files to find out more
information. Or run "grub-install" manually and copy-paste command
invocation and output. If you are using grub2 with EFI install device
is redundant and will be ignored by grub-install anyway.

> 
> My objective is to have Mint installed onto a software RAID1 system that is 
> bootable if either drive failes (or is removed from the system), with minimal 
> downtime by just installing a new drive and resyncing the RAID. I want to 
> avoid additional steps that involve reinstalling grub or the boot files after 
> the failure to make the system bootable again.
> 
> A summary of my disk setup steps are as follows.
> 1. Boot to SystemRescueCD and from a terminal window create a RAID1 array 
> from both drives.
> root# mdadm --create --verbose /dev/md127 --level=1 --raid-devices=2 /dev/sda 
> /dev/sdb
> 
> This displays the standard warning about ensuring that your resulting boot 
> loader understands md/v1.x metadata. Then defaults to using version 1.2 
> metadata. According to the Grub2 manual, Section 1.3, Grub2 can read files 
> directly from LVM and RAID devices, therefore version 1.2 should be ok.
> 
> 2. In GParted, selected the raid device (/dev/md127) and assigned a GPT 
> partition to it.
> 
> 3. Using GParted created 3 partitions on the raid array.
> md127p1 /boot/efi 550 MB FAT32 EFI System Partition, boot & esp flags set

EFI partition cannot be part of MD RAID unless this MD RAID is can also
be accessed by firmware. Command you used creates standard RAID, not
associated with any firmware RAID. 

If you want to use legacy BIOS booting, this will not work in this
configuration either - you need to create partitioned disks, assemble
MD RAIDs from each partition and install bootloader in MBR (outside of
Linux MD).

> md127p2 /boot 550 MB FAT32
> md127p3 2.73 TB Lvm2 Physical Volume
> 
> If I recall correctly, GParted leaves 1 MB untouched before the first 
> partition. Then I left 100 MB unallocated after md127p3.
> 
> 4. From the terminal window, create the following logical volumes.
> root# lvcreate -L 8G -n lv_mintroot vg_jab
> root# lvcreate -L 4G -n lv_mintvar vg_jab
> root# lvcreate -L 2G -n lv_mintswap vg_jab
> root# lvcreate -L 80G -n lv_minthome vg_jab
> root# lvcreate -L 1000G -n lv_mintgis vg_jab
> 
> Side Note: Mint will be a KVM host that will also run a Win7 guest with a 
> couple of additional logical volumes for the Windows guest, hence the naming 
> of logical volumes. I use a similar setup on my CentOS 6 KVM Host Server with 
> several guests and it makes managing the storage easy and understandable.
> 
> 5. Eject the SystemRescueCD and reboot to the Linux Mint LiveCD installer. Do 
> some housekeeping to get Mint to recognize the raid array.
> 
> address@hidden sudo apt-get update
> address@hidden sudo apt-get remove dmraid
> address@hidden sudo apt-get install mdadm
> address@hidden sudo mdadm --examine --scan
>  ARRAY /dev/md/127 metadata=1.2 UUID baf72191:8d8bb4e4:6b31b91a:c0efe33e 
> name=sysresccd:127
> address@hidden sudo mdadm --assemble --scan
>  mdadm: /dev/md/127 has been started with 2 drives
> address@hidden cat /proc/mdstat
>  Personalities : [raid1]
>  md127 : active raid1 sda[0] sdb[1]
> 
> 6. Start the Mint installer and select custom partitioning. The custom 
> partitioning dialog correctly recognizes the raid array, all previously 
> configured partitions, logical volumes, and boot flags.
> 
> 7. Select each partition and logical volume established in steps #2 and #3 
> above and identify the mount point and assign the appropriate file system. 
> The /boot/efi and /boot partitions were formated as shown in step #2 above. 
> The LVM logical volumes were formatted as XFS file systems, except swap.
> 
> 8. In Mint there is a menu list below the custom partitioning to identify and 
> select the location for installing the boot loader. The RAID1 device 
> (/dev/md127) was selected for installing the boot loader (not an individual 
> partition or a single drive).
> 
> 9. Installation progressed normally until the point of installing grub, which 
> resulted in the following error:
> 
> Running grub-install /dev/md127
> Unable to install GRUB in /dev/md127
> Executing ‘grub-install /dev/md127’ failed
> This is a fatal error
> 
> It is my understanding that Mint17.1 is based on Ubuntu 14.04, which includes 
> Grub2. And looking at the documentation for Grub2 includes support for Linux 
> software (mdadm) RAID1, EFI, and GPT. So I don't know what I am missing with 
> this configuration that causes grub-install to fail. I can provide more 
> diagnostic information if necessary, but don't know what may be needed, and I 
> am looking here for some expert advice.
> 
> I am open to suggestions that are oriented towards my objective of having a 
> bootable software RAID1 installation if there is something else I need to 
> consider. Thanks for reading my (long) post.
> 
> Please cc me directly on any replies, as I am subscribed to the daily digest.
> Jeff
> 
> 
> _______________________________________________
> Help-grub mailing list
> address@hidden
> https://lists.gnu.org/mailman/listinfo/help-grub