Re: [Freeipmi-devel] Issue with ipmi-oem supermicro (pmbus) power-supply

Actually, it seems that 00 is good in this case. I asked supermicro for confirmation on all possessible values but haven't heard back yet.

On Sep 9, 2015 1:12 PM, "Albert Chu" <address@hidden> wrote:

That's not too far removed from the other motherboard. From ipmi-oem's
comments:

/* Supermicro OEM
* From Supermicro Engineer
*
* Request
*
* 0x06 - network function
* 0x52 - cmd (master read/write)
* 0x07 - (channel = 0, bus id = 3, bus type = private)
* 0x?? - slave address
* - 0x70 - ps 1
* - 0x72 - ps 2
* - 0x74 - ps 3
* 0x01 - read count
* 0x0c - data to write ... no idea why 0x0c
*
* Response
*
* 0x52 - cmd
* 0x?? - Completion Code
* 0x?? - 0x01 - good
* - 0x00 - bad
*/

I added yours into a branch of FreeIPMI if you could give it a shot. I
just assumed the good vs bad response was the same.

svn co http://svn.savannah.gnu.org/svn/freeipmi/branches/supermicroipmioempower freeipmi
cd freeipmi
./autogen.sh
./configure
make
ipmi-oem/ipmi-oem supermicro get-power-supply-status2 1
ipmi-oem/ipmi-oem supermicro get-power-supply-status2 2

As an aside, after I realized that this was going through the master
read/write and not some arbitrary Supermicro OEM command, I actually can
add an error message for the 83h error code you saw before. So
hopefully that's taken care of when you run the original. I get

# ipmi-oem/ipmi-oem Supermicro get-power-supply-status 1
Supermicro:get-power-supply-status failed: NAK on Write

Al

On Wed, 2015-09-09 at 12:09 -0500, Scott Silverman wrote:
> I assume that was the case. If it helps, I have the following from
> SuperMicro (can only confirm for the listed board, I don't have any
> other X10 to test on):
>
>
> For the X10DRU-i+, please try the command below:
>
> raw 0x06 0x52 0x07 0xb0 0x01 0x0c for power supply 1
>
> raw 0x06 0x52 0x07 0xb2 0x01 0x0c for power supply 2
>
>
>
>
>
>
>
>
>
>
>
> Thanks,
>
>
> Scott Silverman | IT | Simplex | 312-360-2444
> 230 S. LaSalle St., Suite 4-100, Chicago, IL 60604
>
> On Tue, Sep 8, 2015 at 12:21 PM, Albert Chu <address@hidden> wrote:
> Hi Scott,
>
> Thanks for the report. Unfortunately, since this is a
> Supermicro
> specific error, not much we can do except wait for a potential
> update of
> information from Supermicro. I can ping some Supermicro folks
> and see
> if they can help.
>
> Al
>
> On Fri, 2015-09-04 at 11:18 -0500, Scott Silverman wrote:
> > Running the ipmi-oem supermicro
> get-(pmbus-)power-supply-status
> > commands against newer (X10 based) SuperMicro servers
> results in the
> > following error:
> >
> >
> >
> > supermicro:get-pmbus-power-supply-status failed: No error
> message
> > found for command 52h, network function 06h, and completion
> code 83h.
> > Please report to <address@hidden>
> >
> >
> > As requested, I'm reporting.
> >
> >
> > I've attached debug output for the regular and the pmbus
> version. Let
> > me know if there's anything I can do to help further.
> >
> >
> >
> >
> > Thanks,
> >
> >
> > Scott Silverman | IT | Simplex | 312-360-2444
> > 230 S. LaSalle St., Suite 4-100, Chicago, IL 60604
> >
>
> > DISCLAIMER: NOTICE REGARDING PRIVACY AND CONFIDENTIALITY
> >
> > The information contained in and/or accompanying this
> communication is
> > intended only for use by the addressee(s) named herein and
> may contain
> > legally privileged and/or confidential information. If you
> are not the
> > intended recipient of this e-mail, you are hereby notified
> that any
> > dissemination, distribution or copying of this information,
> and any
> > attachments thereto, is strictly prohibited. If you have
> received this
> > e-mail in error, please immediately notify the sender and
> permanently
> > delete the original and any copy of any e-mail and any
> printout
> > thereof. Electronic transmissions cannot be guaranteed to be
> secure or
> > error-free. The sender therefore does not accept liability
> for any
> > errors or omissions in the contents of this message which
> arise as a
> > result of e-mail transmission. Simplex Trading, LLC and its
> affiliates
> > reserves the right to intercept, monitor, and retain
> electronic
> > communications to and from its system as permitted by law.
> Simplex
> > Trading, LLC is a registered Broker Dealer with CBOE and a
> Member of
> > SIPC.
> > _______________________________________________
> > Freeipmi-devel mailing list
> > address@hidden
> > https://lists.gnu.org/mailman/listinfo/freeipmi-devel
> --
> Albert Chu
> address@hidden
> Computer Scientist
> High Performance Systems Division
> Lawrence Livermore National Laboratory
>
>
>
>
>
> DISCLAIMER: NOTICE REGARDING PRIVACY AND CONFIDENTIALITY
>
> The information contained in and/or accompanying this communication is
> intended only for use by the addressee(s) named herein and may contain
> legally privileged and/or confidential information. If you are not the
> intended recipient of this e-mail, you are hereby notified that any
> dissemination, distribution or copying of this information, and any
> attachments thereto, is strictly prohibited. If you have received this
> e-mail in error, please immediately notify the sender and permanently
> delete the original and any copy of any e-mail and any printout
> thereof. Electronic transmissions cannot be guaranteed to be secure or
> error-free. The sender therefore does not accept liability for any
> errors or omissions in the contents of this message which arise as a
> result of e-mail transmission. Simplex Trading, LLC and its affiliates
> reserves the right to intercept, monitor, and retain electronic
> communications to and from its system as permitted by law. Simplex
> Trading, LLC is a registered Broker Dealer with CBOE and a Member of
> SIPC.
--
Albert Chu
address@hidden
Computer Scientist
High Performance Systems Division
Lawrence Livermore National Laboratory

From:	Scott Silverman
Subject:	Re: [Freeipmi-devel] Issue with ipmi-oem supermicro (pmbus) power-supply-status
Date:	Wed, 9 Sep 2015 13:16:30 -0500