[avrdude-dev] support for avr32

[Tobias]

hy!

i am supposed to develop some products using the EVK1100 board (AT32UC3) and 
the jtag ICE mkII. i would like to do development in linux, and as such using 
a 64 bit system, so using avrstudio isn't quite an option either (atleast i 
couldnt make it work properly). i played around with avrdude a bit, but 
either i am making a stupid mistake, or there is some support missing :)

the output of "avrdude -p m32 -P usb -c jtag2isp -v" looks like this 
(copyright etc stripped)

         Using Port            : usb
         Using Programmer      : jtag2isp
avrdude: usbdev_open(): Found JTAGICE mkII, serno: 00B0000029BB
JTAG ICE mkII sign-on message:
Communications protocol version: 1
M_MCU:
  boot-loader FW version:        255
  firmware version:              4.32
  hardware version:              0
S_MCU:
  boot-loader FW version:        255
  firmware version:              4.32
  hardware version:              1
Serial number:                   00:b0:00:00:29:bb
Device ID:                       JTAGICEmkII
avrdude: jtagmkII_setparm(): bad response to set parameter command: RSP_FAILED
avrdude: jtagmkII_getsync(): ISP activation failed, trying debugWire
avrdude: jtagmkII_setparm(): bad response to set parameter command: 
RSP_DEBUGWIRE_SYNC_FAILED
avrdude: failed to sync with the JTAG ICE mkII in ISP mode
avrdude: jtagmkII_close(): timeout/error communicating with programmer 
(status -1)

"avrdude -p m32 -P usb -c jtag2 -v" gives:

         Using Port            : usb
         Using Programmer      : jtag2
avrdude: usbdev_open(): Found JTAGICE mkII, serno: 00B0000029BB
JTAG ICE mkII sign-on message:
Communications protocol version: 1
M_MCU:
  boot-loader FW version:        255
  firmware version:              4.32
  hardware version:              0
S_MCU:
  boot-loader FW version:        255
  firmware version:              4.32
  hardware version:              1
Serial number:                   00:b0:00:00:29:bb
Device ID:                       JTAGICEmkII
         AVR Part              : ATMEGA32
         Chip Erase delay      : 9000 us
         PAGEL                 : PD7
         BS2                   : PA0
         RESET disposition     : dedicated
         RETRY pulse           : SCK
         serial program mode   : yes
         parallel program mode : yes
         Timeout               : 200
         StabDelay             : 100
         CmdexeDelay           : 25
         SyncLoops             : 32
         ByteDelay             : 0
         PollIndex             : 3
         PollValue             : 0x53
         Memory Detail         :

                                  Block Poll               Page                 
      
Polled
           Memory Type Mode Delay Size  Indx Paged  Size   Size #Pages MinW  
MaxW   ReadBack
           ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- 
----- ---------
           eeprom         4    10    64    0 no       1024    4      0  9000  
9000 0xff 0xff
           flash         33     6    64    0 yes     32768  128    256  4500  
4500 0xff 0xff
           lfuse          0     0     0    0 no          1    0      0  2000  
2000 0x00 0x00
           hfuse          0     0     0    0 no          1    0      0  2000  
2000 0x00 0x00
           lock           0     0     0    0 no          1    0      0  2000  
2000 0x00 0x00
           signature      0     0     0    0 no          3    0      0     0    
 
0 0x00 0x00
           calibration    0     0     0    0 no          4    0      0     0    
 
0 0x00 0x00

         Programmer Type : JTAGMKII
         Description     : Atmel JTAG ICE mkII
         M_MCU hardware version: 0
         M_MCU firmware version: 4.32
         S_MCU hardware version: 1
         S_MCU firmware version: 4.32
         Serial number:          00:b0:00:00:29:bb
         Vtarget         : 3.3 V
         JTAG clock      : 891.7 kHz (1.1 us)

avrdude: jtagmkII_program_enable(): bad response to enter progmode command: 
RSP_ILLEGAL_JTAG_ID
avrdude: JTAGEN fuse disabled?
avrdude: initialization failed, rc=-1
         Double check connections and try again, or use -F to override
         this check.

the flash line made me wonder, since this board/mcu has 512k flash (or am i 
interpreting the printed values wrong?).

however, since i really would like to develop in linux (and i am out of hope 
for avr32program to work on 64bit anytime soon) i wouldn't mind adding the 
missing features to avrdude. if someone could give me some 
hints/suggestions/whatever that would be very nice :)

oh and i should say that i can program the board using avrstudio on a windows 
box without problems, so the whole setup is ok as such.

-- 
http://ami.ga/
http://c64upgra.de/