Le 21/03/2014 23:57, evan igor a
écrit :
It looks like your gps and the AP are talking but you just don't get high enough signals to have a fix. How long did you wait ?Hi all ,
thanks so much for you response and the edition added to the wiki i added the module to the airframe but the GPS not fixed
It just means that some buttons in the strip cannot be used, which is not problem since they are only used with fixedwing firmware
and the following warning also i don't know how to solve
On Fri, Mar 21, 2014 at 8:56 AM, Kadir ÇİMENCİ <address@hidden> wrote:
I was flying with default too.. In automative model it says equivalent dynamics for a passenger car..It may not be suitable for sudden direction changes in horizontal like we have in multicopters.. I will try to observe the difference between portable and airborne_2g versions..
2014-03-20 20:19 GMT+02:00 Ben Laurie <address@hidden>:
On 20 March 2014 16:58, Andrew Chambers <address@hidden> wrote:
evan,
I added some more details about what the dynamics models mean on the wiki page:
I think the general recommendation is to use NAV5_DYN_PORTABLE for quadcopters and NAV5_DYN_AIRBORNE_2G for planes. NAV5_DYN_AIRBORNE_2G is set by default if you don't define the GPS_UBX_NAV5_DYNAMICS parameter.
Interesting ... the ARdrone is set up for the default. Looking at the datasheet, I wonder if the automotive model would actually be better for quadcopters? Max vertical velocity of 15 versus 50 m/s, and max horizontal of 84 vs 310 m/s.
On Thu, Mar 20, 2014 at 6:58 AM, Kadir ÇİMENCİ <address@hidden> wrote:
Im not sure that if there is a parameter like that, just add the module it will make the configuration for you. You can just leave the parameters on default but be sure GPS outputs on right UART target which you connect the GPS to your board..
2014-03-20 13:28 GMT+02:00 evan igor <address@hidden>:
should i edit any parameters such as "GPS_UBX_NAV5_DYNAMICS" or just add the module.and for the GPS itself should i edit the output of the GPS protocol such as in the picture
On Thu, Mar 20, 2014 at 1:19 PM, Kadir ÇİMENCİ <address@hidden> wrote:
add the modules section below firmware section in the airframe file..
2014-03-20 12:53 GMT+02:00 evan igor <address@hidden>:
Hi,
i changed the baudrate of the GPS to 9600 from u_center and i'm trying to the module 'gps_ubx_ucenter'
but the following error appear
On Wed, Mar 19, 2014 at 12:00 PM, Ben Laurie <address@hidden> wrote:
On 19 March 2014 05:56, Kadir ÇİMENCİ <address@hidden> wrote:
maybe it is related with the baud rate of your gps(I had a similar problem , ppz ucenter module can't talk with gps when it is configured to 19200 ). Configure the baud rate as 9600 on ublox , then connect gps your ppz. and don't forget to add 'gps_ubx_ucenter' module to your project..
The other problem is you could have the wrong port configured.
Kadir
2014-03-19 4:44 GMT+02:00 Eduardo lavratti <address@hidden>:
open the message windows and lock @ GPS to see if you ppz are receiving any gps message.
way you continue with KILL status ? kill switch with are active ?
Date: Wed, 19 Mar 2014 02:09:22 +0200
From: address@hidden
To: address@hidden
Subject: [Paparazzi-devel] no GPS no navigation route_______________________________________________ Paparazzi-devel mailing list address@hidden https://lists.nongnu.org/mailman/listinfo/paparazzi-devel
Hi,i have lisa/m i connected everything in the same manner as in the wiki but the following errors
1- GPS not fix although it's wirking correctly with u-center.
2- no navigation routine set:
3- error in the main paparazzi s/w
any comments appreciated in advance
_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel
_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel
_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel
_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel
_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel
_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel
_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel
_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel
_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel
_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel
_______________________________________________ Paparazzi-devel mailing list address@hidden https://lists.nongnu.org/mailman/listinfo/paparazzi-devel
