paparazzi-devel
[Top][All Lists]
Advanced
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Paparazzi-devel] Compile error on Ubuntu 13.10

From: Jorn Anke
Subject: Re: [Paparazzi-devel] Compile error on Ubuntu 13.10
Date: Mon, 28 Oct 2013 22:22:27 +0100
Output from the command: /opt/paparazzi/arm-multilib/bin/arm-none-eabi-gcc --version:
bash: /opt/paparazzi/arm-multilib/bin/arm-none-eabi-gcc: cannot execute binary file

(This was from after I had downloaded, unpacked, added the toolchain to path).

Maybe the problem is related to Ubuntu 13.10 is still not supported? From the release notes:
Supported hosts:
* Windows XP/7 32/64 bits (with installer and alternative zip package)
* Linux 32/64 bits
  - Ubuntu 8.x or later (tarball)
  - Ubuntu 10.04/12.04/13.04 (tarball and PPA)
  - RHEL 4/5 (tarball)


Jørn


Date: Mon, 28 Oct 2013 20:30:09 +0100
From: address@hidden
To: address@hidden
Subject: Re: [Paparazzi-devel] Compile error on Ubuntu 13.10

Hm... can you please run /opt/paparazzi/arm-multilib/bin/arm-none-eabi-gcc --version ?

I don't have a 13.10 machine to test, but maybe the paparazzi arm-multilib toolchain needs to updated/rebuilt for it.

In any case, (since you are using paparazzi_version >= 5.0) the recommended toolchain is the gcc-arm-embedded one from launchpad.
Can you please download and unpack the tarball and add the ~/home/<unpack_dir>/bin to your PATH variable and test again?
export PATH=~/home/<unpack_dir>/bin:$PATH


On Mon, Oct 28, 2013 at 8:06 PM, Jorn Anke <address@hidden> wrote:
Also the other example files I have tested ends with error messages like:


/opt/paparazzi/arm-multilib/bin/arm-none-eabi-gcc: 2: /opt/paparazzi/arm-multilib/bin/arm-none-eabi-gcc: Syntax error: "(" unexpected

Output from command: address@hidden:~/paparazzi$ make AIRCRAFT=My_Lisa_Skywalker ap.compile Q=""


-----------------------------------------------------------------------
Paparazzi version v5.1_devel-569-g3fe72e2
-----------------------------------------------------------------------
if (expr "My_Lisa_Skywalker"); then : ; else echo "AIRCRAFT undefined: type 'make AIRCRAFT=AircraftName ...'"; exit 1; fi

My_Lisa_Skywalker
BUILD My_Lisa_Skywalker, TARGET ap
PAPARAZZI_SRC=/home/jorn/paparazzi PAPARAZZI_HOME=/home/jorn/paparazzi TARGET=ap Q= /home/jorn/paparazzi/sw/tools/gen_aircraft.out My_Lisa_Skywalker
make -f Makefile.ac AIRCRAFT=My_Lisa_Skywalker AC_ID=1 AIRFRAME_XML=airframes/TUDelft/my_lisa_m2_test6.xml TELEMETRY=telemetry/default_fixedwing.xml SETTINGS=" settings/fixedwing_basic.xml settings/modules/dc.xml" MD5SUM="4ac57c8e175ecea8030fb3d20e0efc6a" TARGET=ap all_ac_h

make[1]: Entering directory `/home/jorn/paparazzi'
make[1]: Leaving directory `/home/jorn/paparazzi'
make -f Makefile.ac AIRCRAFT=My_Lisa_Skywalker AC_ID=1 AIRFRAME_XML=airframes/TUDelft/my_lisa_m2_test6.xml TELEMETRY=telemetry/default_fixedwing.xml SETTINGS=" settings/fixedwing_basic.xml settings/modules/dc.xml" MD5SUM="4ac57c8e175ecea8030fb3d20e0efc6a" RADIO=radios/R6107SP_7ch.xml radio_ac_h

make[1]: Entering directory `/home/jorn/paparazzi'
make[1]: Nothing to be done for `radio_ac_h'.

make[1]: Leaving directory `/home/jorn/paparazzi'
make -f Makefile.ac AIRCRAFT=My_Lisa_Skywalker AC_ID=1 AIRFRAME_XML=airframes/TUDelft/my_lisa_m2_test6.xml TELEMETRY=telemetry/default_fixedwing.xml SETTINGS=" settings/fixedwing_basic.xml settings/modules/dc.xml" MD5SUM="4ac57c8e175ecea8030fb3d20e0efc6a" FLIGHT_PLAN=flight_plans/basic.xml flight_plan_ac_h

make[1]: Entering directory `/home/jorn/paparazzi'
make[1]: Nothing to be done for `flight_plan_ac_h'.

make[1]: Leaving directory `/home/jorn/paparazzi'
cd sw/airborne; make TARGET=ap all
Using "arch/stm32/lisa-m.ld" as ldscript for target "ap".
make[1]: Entering directory `/home/jorn/paparazzi/sw/airborne'

Using CC   = /opt/paparazzi/arm-multilib/bin/arm-none-eabi-gcc
Using LD   = /opt/paparazzi/arm-multilib/bin/arm-none-eabi-gcc
Using CP   = /opt/paparazzi/arm-multilib/bin/arm-none-eabi-objcopy
Using DMP  = /opt/paparazzi/arm-multilib/bin/arm-none-eabi-objdump
Using NM   = /opt/paparazzi/arm-multilib/bin/arm-none-eabi-nm
Using SIZE = /opt/paparazzi/arm-multilib/bin/arm-none-eabi-size
GCC version:
/opt/paparazzi/arm-multilib/bin/arm-none-eabi-gcc: 2: /opt/paparazzi/arm-multilib/bin/arm-none-eabi-gcc: Syntax error: "(" unexpected

CC /home/jorn/paparazzi/var/My_Lisa_Skywalker/ap/mcu.o
test -d /home/jorn/paparazzi/var/My_Lisa_Skywalker/ap/ || mkdir -p /home/jorn/paparazzi/var/My_Lisa_Skywalker/ap/
/opt/paparazzi/arm-multilib/bin/arm-none-eabi-gcc -c -I. -I./stm32 -I../ext/libopencm3/include -I/home/jorn/paparazzi/sw/include -I/home/jorn/paparazzi/sw/airborne -I/home/jorn/paparazzi/conf/autopilot -I/home/jorn/paparazzi/sw/airborne/arch/stm32 -I/home/jorn/paparazzi/var/include -I/home/jorn/paparazzi/var/My_Lisa_Skywalker -D__thumb2__ -Wall -Os -msoft-float -Wl,--gc-sections -mfix-cortex-m3-ldrd -mcpu=cortex-m3 -mthumb -ansi -std=gnu99 -fno-common -g -ffunction-sections -fdata-sections -Wimplicit -Wcast-align -Wpointer-arith -Wswitch -Wredundant-decls -Wreturn-type -Wshadow -Wunused -Wa,-adhlns=/home/jorn/paparazzi/var/My_Lisa_Skywalker/ap/mcu.lst -Wnested-externs -Wmissing-prototypes -Wstrict-prototypes -Wmissing-declarations -Wswitch-default -DSTM32F1 -DACTUATORS -DAHRS_ALIGNER_LED=2 -DAHRS_CORRECT_FREQUENCY=100 -DAHRS_PROPAGATE_FREQUENCY=100 -DAHRS_TRIGGERED_ATTITUDE_LOOP -DAHRS_TYPE_H=\"subsystems/ahrs/ahrs_float_dcm.h\" -DAHRS_UPDATE_FW_ESTIMATOR -DALT_KALMAN -DAP -DASPIRIN_2_SPI_DEV=spi2 -DASPIRIN_2_SPI_SLAVE_IDX=SPI_SLAVE2 -DBB_MS5611_SLAVE_IDX=SPI_SLAVE3 -DBB_MS5611_SPI_DEV=spi2 -DBOARD_CONFIG=\"boards/lisa_m_2.0.h\" -DCTRL_TYPE_H=\"firmwares/fixedwing/guidance/guidance_v.h\" -DDATALINK=PPRZ -DDC_PUSH=LED_OFF -DDC_RELEASE=LED_ON -DDC_SHUTTER_DELAY=4 -DDC_SHUTTER_LED=7 -DDIGITAL_CAM -DDOWNLINK -DDOWNLINK_AP_DEVICE=UART2 -DDOWNLINK_FBW_DEVICE=UART2 -DDOWNLINK_TRANSPORT=PprzTransport -DFBW -DFIRMWARE=FIXEDWING -DGPS_LED=3 -DGPS_LINK=UART3 -DGPS_TYPE_H=\"subsystems/gps/gps_ubx.h\" -DGPS_UBX_UCENTER=\"modules/gps/gps_ubx_ucenter.c\" -DGPS_USE_LATLONG -DIMU_TYPE_H=\"imu/imu_aspirin_2_spi.h\" -DINS_TYPE_H=\"subsystems/ins/ins_alt_float.h\" -DINTER_MCU -DLED_7_BANK=0 -DLED_7_PIN=22 -DLUFTBOOT -DNAV -DPERIODIC_FREQUENCY=120 -DPERIPHERALS_AUTO_INIT -DPPRZ_UART=UART2 -DRADIO_CONTROL -DRADIO_CONTROL_LED=4 -DRADIO_CONTROL_TYPE_H=\"subsystems/radio_control/ppm.h\" -DRADIO_CONTROL_TYPE_PPM -DSENSOR_SYNC_SEND=1 -DSPI_MASTER -DSYS_TIME_LED=1 -DTRAFFIC_INFO -DUART2_BAUD=B57600 -DUART3_BAUD=B38400 -DUBX -DUSE_ADC -DUSE_AHRS -DUSE_AHRS_ALIGNER -DUSE_GPS -DUSE_IMU -DUSE_LED -DUSE_LED_7=1 -DUSE_MAGNETOMETER=FALSE -DUSE_SPI -DUSE_SPI2 -DUSE_SPI_SLAVE2 -DUSE_SPI_SLAVE3 -DUSE_SYS_TIME -DUSE_UART2 -DUSE_UART3 -DWIND_INFO -I. -Iarch/stm32/modules -Iboards/lisa_m -Ifirmwares/fixedwing -Imodules mcu.c -o /home/jorn/paparazzi/var/My_Lisa_Skywalker/ap/mcu.o

/opt/paparazzi/arm-multilib/bin/arm-none-eabi-gcc: 2: /opt/paparazzi/arm-multilib/bin/arm-none-eabi-gcc: Syntax error: "(" unexpected
make[1]: *** [/home/jorn/paparazzi/var/My_Lisa_Skywalker/ap/mcu.o] Error 2
make[1]: Leaving directory `/home/jorn/paparazzi/sw/airborne'
make: *** [ap.compile] Error 2




Date: Mon, 28 Oct 2013 19:53:42 +0100

From: address@hidden
To: address@hidden
Subject: Re: [Paparazzi-devel] Compile error on Ubuntu 13.10

Or run make AIRCRAFT=My_Lisa_Skywalker ap.compile Q="" from the comandline and post the output...


On Mon, Oct 28, 2013 at 7:45 PM, Felix Ruess <address@hidden> wrote:
Hi Jorn,

Do other (example) aircrafts compile?

Did you clean the aircraft again afterwards? That would delete your aircraft folder in var.
Please run it again and attach the ap_srcs.list from /home/jorn/paparazzi/var/My_Lisa_Skywalker/

Cheers, Felix


On Mon, Oct 28, 2013 at 7:23 PM, Jorn Anke <address@hidden> wrote:
Thanks for the reply Felix :-)

The airframe file is pasted under. There were however no "ap" sub-folder (or .depend-file) in /home/jorn/paparazzi/var/My_Lisa_Skywalker/...


Cheers, Jørn

_________________________

<!DOCTYPE airframe SYSTEM "../airframe.dtd">

<!-- this is a Skywalker
  * Autopilot:   Lisa/M 2.0         http://paparazzi.enac.fr/wiki/Lisa/M_v20
  * IMU:         Aspirin 2.2        http://paparazzi.enac.fr/wiki/AspirinIMU
  * GPS:         Ublox              http://paparazzi.enac.fr/wiki/Subsystem/gps
  * RC:          any PPM system     http://paparazzi.enac.fr/wiki/Subsystem/radio_control#PPM
  * Modem        XBee in transparent mode at 57600 baud
-->

<airframe name="Skywalker LisaM 2.0">

  <!-- commands section -->
  <servos>
    <servo name="THROTTLE"      no="1" min="1000" neutral="1000" max="2000"/>
    <servo name="AILERON_RIGHT" no="4" min="900" neutral="1500" max="2100"/>
    <servo name="AILERON_LEFT"  no="5" min="900" neutral="1500" max="2100"/>
    <servo name="ELEVATOR"      no="2" min="1900" neutral="1500" max="1100"/>
    <servo name="RUDDER"        no="3" min="900" neutral="1350" max="1800"/>
  </servos>

  <commands>
    <axis name="THROTTLE" failsafe_value="0"/>
    <axis name="ROLL" failsafe_value="0"/>
    <axis name="PITCH" failsafe_value="0"/>
    <axis name="YAW" failsafe_value="0"/>
    <axis name="BRAKE" failsafe_value="9600"/>    <!-- both elerons up as butterfly brake ? -->
  </commands>

  <rc_commands>
    <set command="THROTTLE" value="@THROTTLE"/>
    <set command="ROLL" value="@ROLL"/>
    <set command="YAW" value="@YAW"/>
    <set command="PITCH" value="@PITCH"/>
    <set command="BRAKE" value="@FLAPS"/>
  </rc_commands>

  <section name="SERVO_MIXER_GAINS">
    <define name="AILERON_NEUTRAL" value="0.3f"/>
    <define name="AILERON_RATE_UP" value="1.0f"/>
    <define name="AILERON_RATE_DOWN" value="0.5f"/>
    <define name="AILERON_RATE_UP_BRAKE" value="1.0f"/>
    <define name="AILERON_RATE_DOWN_BRAKE" value="1.0f"/>
    <define name="PITCH_GAIN" value="0.9f"/>
    <define name="BRAKE_AILEVON" value="-0.7f"/>
    <define name="BRAKE_PITCH" value="0.1f"/>
    <define name="MAX_BRAKE_RATE" value="130"/>
    <define name="RUDDER_OF_AILERON" value="0.3"/>
  </section>

  <!-- New settings pr. 20. jan. 2013 -->
  <command_laws>
    <!-- Brake Rate Limiter -->
    <let var="brake_value_nofilt" value="Chop(address@hidden, 0, MAX_PPRZ)"/>
    <ratelimit var="brake_value" value="$brake_value_nofilt" rate_min="-MAX_BRAKE_RATE" rate_max="MAX_BRAKE_RATE" />
    <!-- Differential Aileron Depending on Brake Value -->
    <let var="aileron_up_rate" value="(AILERON_RATE_UP * (MAX_PPRZ - $brake_value)) + (AILERON_RATE_UP_BRAKE * $brake_value)"/>
    <let var="aileron_down_rate" value="(AILERON_RATE_DOWN * (MAX_PPRZ - $brake_value)) + (AILERON_RATE_DOWN_BRAKE * $brake_value)"/>
    <let var="aileron_up" value="((address@hidden) * (((float)$aileron_up_rate) / ((float)MAX_PPRZ)))"/>
    <let var="aileron_down" value="((address@hidden) * (((float)$aileron_down_rate) / ((float)MAX_PPRZ)))"/>
    <let var="leftturn" value="(@ROLL >= 0? 0 : 1)"/>
    <let var="rightturn" value="(1 - $leftturn)"/>
    <set servo="AILERON_LEFT" value="($aileron_up * $leftturn) + ($aileron_down * $rightturn) - $brake_value*(BRAKE_AILEVON) - (MAX_PPRZ * AILERON_NEUTRAL)"/>
    <set servo="AILERON_RIGHT" value="($aileron_up * $rightturn) + ($aileron_down * $leftturn) + $brake_value*(BRAKE_AILEVON) + (MAX_PPRZ *AILERON_NEUTRAL)"/>
    <set servo="RUDDER" value="-(@YAW + @ROLL * RUDDER_OF_AILERON)"/>
    <set servo="THROTTLE" value="@THROTTLE"/>
    <!-- Pitch with Brake-Trim Function -->
    <set servo="ELEVATOR" value="@PITCH * PITCH_GAIN - BRAKE_PITCH * $brake_value"/>
  </command_laws>

  <section name="AUTO1" prefix="AUTO1_">
    <define name="MAX_ROLL" value="60.0"  unit="deg"/>
    <define name="MAX_PITCH" value="45.0" unit="deg"/>
  </section>

  <section name="BAT">
    <!-- <define name="MILLIAMP_AT_FULL_THROTTLE" value="20000" unit="mA"/> -->
    <define name="CATASTROPHIC_BAT_LEVEL" value="9.0" unit="V"/>
    <define name="CRITIC_BAT_LEVEL" value="9.5" unit="V"/>
    <define name="LOW_BAT_LEVEL" value="10.0" unit="V"/>
    <define name="MAX_BAT_LEVEL" value="12.5" unit="V"/>
  </section>
 
  <section name="INS" prefix="INS_">
    <define name="ROLL_NEUTRAL_DEFAULT"  value="0" unit="deg"/>
    <define name="PITCH_NEUTRAL_DEFAULT" value="0" unit="deg"/>
    <define name="BARO_SENS" value="22.3" integer="16"/>
  </section>

  <section name="MISC">
    <define name="NOMINAL_AIRSPEED" value="14." unit="m/s"/>
    <define name="CARROT" value="5." unit="s"/>
    <define name="CONTROL_FREQUENCY" value="60" unit="Hz"/>
    <!-- Ny parameter satt inn 17.09.2012 -->
    <define name="NAV_RADIUS" value="50" unit="m"/>
    <!-- XBEE kommentert ut 19.02.2013 (433MHz moduler)-->
    <!-- <define name="XBEE_INIT" value="&quot;ATPL2\rATRN5\rATTT80\r&quot;"/> -->
    <!-- v<define name="ALT_KALMAN_ENABLED" value="TRUE"/> -->
    <define name="DEFAULT_CIRCLE_RADIUS" value="50."/>
    <define name="GLIDE_AIRSPEED" value="10"/>
    <define name="GLIDE_VSPEED" value="3."/>
    <define name="GLIDE_PITCH" value="45" unit="deg"/>
    <define name="COMMAND_ROLL_TRIM" value="180"/>
    <define name="COMMAND_PITCH_TRIM" value="-194."/>
  </section>

  <section name="VERTICAL CONTROL" prefix="V_CTL_">
    <define name="POWER_CTL_BAT_NOMINAL" value="11.1" unit="volt"/>
    <!-- outer loop proportional gain -->
    <define name="ALTITUDE_PGAIN" value="0.108000002801"/>
    <!-- outer loop saturation -->
    <define name="ALTITUDE_MAX_CLIMB" value="2."/>
    <!-- auto throttle inner loop -->
    <define name="AUTO_THROTTLE_NOMINAL_CRUISE_THROTTLE" value="0.43599998951"/>
    <define name="AUTO_THROTTLE_MIN_CRUISE_THROTTLE" value="0.25"/>
    <define name="AUTO_THROTTLE_MAX_CRUISE_THROTTLE" value="0.549000024796"/>
    <define name="AUTO_THROTTLE_LOITER_TRIM" value="1500"/>
    <define name="AUTO_THROTTLE_DASH_TRIM" value="-4000"/>
    <define name="AUTO_THROTTLE_CLIMB_THROTTLE_INCREMENT" value="0.158000007272" unit="%/(m/s)"/>
    <define name="AUTO_THROTTLE_PGAIN" value="0."/>
    <define name="AUTO_THROTTLE_IGAIN" value="0."/>
    <define name="AUTO_THROTTLE_PITCH_OF_VZ_PGAIN" value="0.361000001431"/>
    <define name="THROTTLE_SLEW_LIMITER" value="2" unit="s"/>
  </section>

  <section name="HORIZONTAL CONTROL" prefix="H_CTL_">
    <define name="COURSE_PGAIN" value="0.972000002861"/>
    <define name="COURSE_DGAIN" value="0.280999988317"/>
    <define name="COURSE_PRE_BANK_CORRECTION" value="1.0039999485"/>
    <define name="ROLL_MAX_SETPOINT" value="0.851999998093" unit="radians"/>
    <define name="PITCH_MAX_SETPOINT" value="0.5" unit="radians"/>
    <define name="PITCH_MIN_SETPOINT" value="-0.5" unit="radians"/>
    <define name="PITCH_PGAIN" value="16917.2929688"/>
    <define name="PITCH_DGAIN" value="7.73400020599"/>
    <define name="ELEVATOR_OF_ROLL" value="3007.81298828"/>
    <define name="ROLL_SLEW" value="1."/>
    <define name="ROLL_ATTITUDE_GAIN" value="11718.75"/>
    <define name="ROLL_RATE_GAIN" value="820.312011719"/>
  </section>

  <section name="AGGRESSIVE" prefix="AGR_">
    <define name="BLEND_START" value="30"/>
    <define name="BLEND_END" value="15"/>
    <define name="CLIMB_THROTTLE" value="1."/>
    <define name="CLIMB_PITCH" value="0.40000000596"/>
    <define name="DESCENT_THROTTLE" value="0."/>
    <define name="DESCENT_PITCH" value="-0.10000000149"/>
    <define name="CLIMB_NAV_RATIO" value="0.800000011921"/>
    <define name="DESCENT_NAV_RATIO" value="0.834999978542"/>
  </section>

  <section name="FAILSAFE" prefix="FAILSAFE_">
    <define name="DEFAULT_THROTTLE" value="0.35" unit="%"/>
    <define name="DEFAULT_ROLL" value="0.17" unit="rad"/>
    <define name="DEFAULT_PITCH" value="0.08" unit="rad"/>
    <define name="HOME_RADIUS" value="DEFAULT_CIRCLE_RADIUS" unit="m"/>
    <define name="KILL_MODE_DISTANCE" value="(MAX_DIST_FROM_HOME*1.3)"/>
    <define name="DELAY_WITHOUT_GPS" value="3" unit="s"/>
  </section>

  <section name="IMU" prefix="IMU_">
    <!-- My settings for orienting Lisa M2 in the flight direction -->
    <define name="BODY_TO_IMU_PHI"   value="0.0" unit="deg"/>
    <define name="BODY_TO_IMU_THETA" value="0.0" unit="deg"/>
    <define name="BODY_TO_IMU_PSI"   value="270.0" unit="deg"/>

    <!-- Default Aspirin V2.1 values based on the datasheet -->
    <!-- Copy/paste from: https://github.com/psinha/paparazzi/blob/toytronics/conf/airframes/esden/calib/asp21-default.xml -->
    <!-- Calibration Neutral -->
    <!--
    <define name="GYRO_P_NEUTRAL" value="0"/>
    <define name="GYRO_Q_NEUTRAL" value="0"/>
    <define name="GYRO_R_NEUTRAL" value="-7"/>
    -->
    <!--SENS = 16.4 LSB/(deg/sec) * 57.6 deg/rad = 939.650 LSB/rad/sec / 12bit FRAC: 4096 / 939.65 -->
    <!--
    <define name="GYRO_P_SENS" value="4.359" integer="16"/>
    <define name="GYRO_Q_SENS" value="4.359" integer="16"/>
    <define name="GYRO_R_SENS" value="4.359" integer="16"/>

    <define name="ACCEL_X_NEUTRAL" value="0"/>
    <define name="ACCEL_Y_NEUTRAL" value="0"/>
    <define name="ACCEL_Z_NEUTRAL" value="0"/>
    <define name="ACCEL_X_SENS" value="4.92297204167" integer="16"/>
    <define name="ACCEL_Y_SENS" value="4.88255070466" integer="16"/>
    <define name="ACCEL_Z_SENS" value="4.86606505696" integer="16"/>

    <define name="MAG_X_NEUTRAL" value="0"/>
    <define name="MAG_Y_NEUTRAL" value="0"/>
    <define name="MAG_Z_NEUTRAL" value="0"/>
    <define name="MAG_X_SENS" value="1" integer="16"/>
    <define name="MAG_Y_SENS" value="1" integer="16"/>
    <define name="MAG_Z_SENS" value="1" integer="16"/>
    -->
  </section>

  <!--
  <section name="SIMULATOR" prefix="NPS_">
    <define name="ACTUATOR_NAMES" value="{&quot;front_motor&quot;, &quot;back_motor&quot;, &quot;right_motor&quot;, &quot;left_motor&quot;}"/>
    <define name="INITIAL_CONDITITONS" value="&quot;reset00&quot;"/>
    <define name="SENSORS_PARAMS" value="&quot;nps_sensors_params_default.h&quot;"/>
  </section>
  -->

  <!--
  <makefile>
    # Virtual AC
    ap.srcs += sw/airborne/subsystems/navigation/zamboni_survey.c
   
  </makefile>
  -->
 
  <section name="DIGITAL_CAMERA" prefix="DC_">
    <!-- <define name="AUTOSHOOT_QUARTERSEC_PERIOD" value="8" unit="quarter_second"/> -->
    <!-- <define name="AUTOSHOOT_METER_GRID" value="50" unit="meter"/> -->
  </section>

  <modules>

    <load name="gps_ubx_ucenter.xml"/>
   
    <!-- <load name="ins_chimu_spi.xml" >
      <define name="CHIMU_BIG_ENDIAN" />
    </load> -->
   
    <!-- <load name="dc.xml"/> -->
    <load name="digital_cam.xml">
      <define name="DC_SHUTTER_LED" value="7"/>
      <define name="LED_7_BANK" value="0"/>
      <define name="LED_7_PIN" value="22"/>
      <define name="USE_LED_7" value="1"/>

      <!--      
        <define name="PUSH" value="LED_ON" />
        <define name="RELEASE" value="LED_OFF" />
       -->

      <define name="DC_RELEASE" value="LED_ON" />  <!-- zero volt on startup -->
      <define name="DC_PUSH" value="LED_OFF" />  <!-- 3.3 volt to trigger -->
      <define name="DC_SHUTTER_DELAY" value="4" unit="quarter_second"/>
      <define name="SENSOR_SYNC_SEND" value="1" />
    </load>

  </modules>


  <firmware name="fixedwing">
    <target name="ap" board="lisa_m_2.0">
      <!-- higher frequency for aspirin imu, ouputs data at 100Hz -->
      <configure name="LISA_M_BARO" value="BARO_MS5611_SPI"/>
      <configure name="PERIODIC_FREQUENCY" value="120"/>
      <configure name="AHRS_PROPAGATE_FREQUENCY" value="100"/>
      <configure name="AHRS_CORRECT_FREQUENCY" value="100"/>
      <define name="AHRS_TRIGGERED_ATTITUDE_LOOP"/>
    </target>

    <target name="sim" board="pc"/>
    <!--
    <target name="nps" board="pc">
      <subsystem name="fdm" type="jsbsim"/>
      <subsystem name="radio_control" type="ppm"/>
    </target>
    -->

    <define name="ALT_KALMAN"/>
    <define name="USE_MAGNETOMETER" value="FALSE"/>

    <subsystem name="radio_control" type="ppm"/>
    <subsystem name="telemetry" type="transparent"/>
    <subsystem name="control"/>
    <subsystem name="imu" type="aspirin_v2.1"/>
    <subsystem name="ahrs" type="float_dcm"/>
    <subsystem name="gps" type="ublox"/>
    <subsystem name="navigation"/>
    <!-- <subsystem name="ins"/> -->
    <subsystem name="ins" type="alt_float"/>
  </firmware>

</airframe>
____________________________________







Date: Mon, 28 Oct 2013 14:04:45 +0100
From: address@hidden
To: address@hidden
Subject: Re: [Paparazzi-devel] Compile error on Ubuntu 13.10


Hi Jorge,

could you please post a link to your configuration/airframe file to reproduce this?
Most likely it is an error in your setup..
Maybe you can also post the /home/jorn/paparazzi/var/My_Lisa_Skywalker/ap/.depend file (where it fails).

Cheers, Felix


On Sun, Oct 27, 2013 at 10:52 PM, Eduardo lavratti <address@hidden> wrote:
i am using ubuntu 13.10 without problems.
From: address@hidden
To: address@hidden
Date: Sun, 27 Oct 2013 22:46:25 +0100
Subject: [Paparazzi-devel] Compile error on Ubuntu 13.10


After upgrading to Ubuntu 13.10 and reinstalling paparazzi, I am having an error messages when compiling as copy&pasted under. Anyone who can see what is going wrong ?


Cheers,

Jorn


 

RUN 'make -C /home/jorn/paparazzi -f Makefile.ac AIRCRAFT=My_Lisa_Skywalker clean_ac '
make: Entering directory `/home/jorn/paparazzi'
My_Lisa_Skywalker
rm -fr /home/jorn/paparazzi/var/My_Lisa_Skywalker
make: Leaving directory `/home/jorn/paparazzi'

DONE 'make -C /home/jorn/paparazzi -f Makefile.ac AIRCRAFT=My_Lisa_Skywalker clean_ac'

RUN 'make -C /home/jorn/paparazzi -f Makefile.ac AIRCRAFT=My_Lisa_Skywalker ap.compile '
make: Entering directory `/home/jorn/paparazzi'
-----------------------------------------------------------------------
Paparazzi version v5.1_devel-569-g3fe72e2
-----------------------------------------------------------------------
My_Lisa_Skywalker
BUILD My_Lisa_Skywalker, TARGET ap
make[1]: Entering directory `/home/jorn/paparazzi'
GENERATE /home/jorn/paparazzi/var/My_Lisa_Skywalker/generated/airframe.h
##################################################
 AIRFRAME MODEL: My_Lisa_Skywalker
##################################################
GENERATE /home/jorn/paparazzi/var/My_Lisa_Skywalker/generated/modules.h
GENERATE /home/jorn/paparazzi/var/My_Lisa_Skywalker/generated/periodic_telemetry.h
GENERATE /home/jorn/paparazzi/var/My_Lisa_Skywalker/generated/settings.h
GENERATE /home/jorn/paparazzi/var/My_Lisa_Skywalker/generated/autopilot_core.h
make[1]: Leaving directory `/home/jorn/paparazzi'
make[1]: Entering directory `/home/jorn/paparazzi'
GENERATE /home/jorn/paparazzi/var/My_Lisa_Skywalker/generated/radio.h
##################################################
 RADIO MODEL: FASST TX Module
##################################################
make[1]: Leaving directory `/home/jorn/paparazzi'
make[1]: Entering directory `/home/jorn/paparazzi'
GENERATE /home/jorn/paparazzi/var/My_Lisa_Skywalker/generated/flight_plan.h
##################################################
 FLIGHT PLAN: Test zamboni
##################################################

Warning: low altitude (240<185+60) in <waypoint Y="160" X="-180" NAME="AF" ALT="240"/>


Warning: low altitude (170<185+60) in <waypoint Y="10" X="-20" NAME="TD" ALT="170.0"/>

GENERATE /home/jorn/paparazzi/var/My_Lisa_Skywalker/flight_plan.xml
make[1]: Leaving directory `/home/jorn/paparazzi'
cd sw/airborne; make TARGET=ap all
Using "arch/stm32/lisa-m.ld" as ldscript for target "ap".
make[1]: Entering directory `/home/jorn/paparazzi/sw/airborne'
DEPEND /home/jorn/paparazzi/var/My_Lisa_Skywalker/ap/.depend
/opt/paparazzi/arm-multilib/bin/arm-none-eabi-gcc: 2: /opt/paparazzi/arm-multilib/bin/arm-none-eabi-gcc: Syntax error: "(" unexpected
make[1]: Leaving directory `/home/jorn/paparazzi/sw/airborne'
Using "arch/stm32/lisa-m.ld" as ldscript for target "ap".
make[1]: Entering directory `/home/jorn/paparazzi/sw/airborne'

Using CC   = /opt/paparazzi/arm-multilib/bin/arm-none-eabi-gcc
Using LD   = /opt/paparazzi/arm-multilib/bin/arm-none-eabi-gcc
Using CP   = /opt/paparazzi/arm-multilib/bin/arm-none-eabi-objcopy
Using DMP  = /opt/paparazzi/arm-multilib/bin/arm-none-eabi-objdump
Using NM   = /opt/paparazzi/arm-multilib/bin/arm-none-eabi-nm
Using SIZE = /opt/paparazzi/arm-multilib/bin/arm-none-eabi-size
GCC version:
/opt/paparazzi/arm-multilib/bin/arm-none-eabi-gcc: 2: /opt/paparazzi/arm-multilib/bin/arm-none-eabi-gcc: Syntax error: "(" unexpected

CC /home/jorn/paparazzi/var/My_Lisa_Skywalker/ap/mcu.o
/opt/paparazzi/arm-multilib/bin/arm-none-eabi-gcc: 2: /opt/paparazzi/arm-multilib/bin/arm-none-eabi-gcc: Syntax error: "(" unexpected
make[1]: *** [/home/jorn/paparazzi/var/My_Lisa_Skywalker/ap/mcu.o] Error 2
make[1]: Leaving directory `/home/jorn/paparazzi/sw/airborne'
make: *** [ap.compile] Error 2
make: Leaving directory `/home/jorn/paparazzi'

FAILED 'make -C /home/jorn/paparazzi -f Makefile.ac AIRCRAFT=My_Lisa_Skywalker ap.compile' with code 2



Cheers,

Jorn

_______________________________________________ Paparazzi-devel mailing list address@hidden https://lists.nongnu.org/mailman/listinfo/paparazzi-devel

_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel



_______________________________________________ Paparazzi-devel mailing list address@hidden https://lists.nongnu.org/mailman/listinfo/paparazzi-devel

_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel




_______________________________________________ Paparazzi-devel mailing list address@hidden https://lists.nongnu.org/mailman/listinfo/paparazzi-devel

_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel



_______________________________________________ Paparazzi-devel mailing list address@hidden https://lists.nongnu.org/mailman/listinfo/paparazzi-devel
reply via email to
[Prev in Thread] Current Thread [Next in Thread]