Re: [Dvdrtools-users] LiteOn SOHW 1633S

[Maurizio Manfredini]

I have the same problem with dvdrecord 0.2.1 on Linux 2.4.20-31.9, just 
trying to burn DVD-R media on PHILIPS DVD+/-R(W): appearently a second 
track is generated, and the first is skipped, resulting in a "logical 
block address out of range" error.

In my case DVD+R media resulted in the wrong driver to be loaded, with 
no burn even started.

command:
dvdrecord -vv -dummy -dao -eject dvdimage.iso

output:
Cdrecord 1.11a15 (i686-pc-linux-gnu) Copyright (C) 1995-2001 J?rg Schilling
TOC Type: 1 = CD-ROM
scsidev: '0,0,0'
scsibus: 0 target: 0 lun: 0
Linux sg driver version: 3.1.24
Using libscg version 'bero-0.5a'
dvdrecord: Warning: using inofficial version of libscg (bero-0.5a 
'@(#)scsitransp.c     1.81 01/04/20 Copyright 1988,1995,2000 J. Schilling').
Using libscg transport code version 'schily-dvdrecord-scsi-linux-sg.c-1.69'
atapi: 1
Device type    : Removable CD-ROM
Version        : 0
Response Format: 2
Capabilities   :
Vendor_info    : 'PHILIPS '
Identifikation : 'DVDR1640P       '
Revision       : 'P2.1'
Device seems to be: Generic mmc2 DVD.
Using generic SCSI-3/mmc DVD-R(W) driver (mmc_mdvd).
Driver flags   : SWABAUDIO BURNFREE
Supported modes: PACKET SAO
Drive buf size : 688128 = 672 KB
FIFO size      : 4194304 = 4096 KB
Track 01: data  1660 MB
track: 1 start: 0 pregap: 150
Total size:     1907 MB (188:56.10) = 850208 sectors
Lout start:     1907 MB (188:58/08) = 850208 sectors
41 00 00 14 00 00 00 00
41 01 00 10 00 00 00 00
41 01 01 10 00 00 02 00
41 AA 01 14 00 BC 3A 08
Track 1 start 0
Track 2 start 850208
41 00 A0 00 00 00 00 01 00 00 00 00
41 00 A1 00 00 00 00 01 00 00 00 00
41 00 A2 00 00 00 00 F8 58 08 00 00
41 00 01 00 00 00 00 00 02 00 00 00
Current Secsize: 2048
 ATIP start of lead in:  -150 (00:00/00)
Disk type:    unknown dye (reserved id code)
Manuf. index: -1
Manufacturer: unknown (not in table)
Blocks total: 2298496 Blocks current: 2298496 Blocks remaining: 1448288
Starting to write CD/DVD at speed 16 in dummy mode for single session.
Last chance to quit, starting dummy write in 0 seconds. Operation starts.
Waiting for reader process to fill input buffer ... input buffer ready.
trackno=0
BURN-Free is ON.
Sending CUE sheet...
Starting new track at sector: 850374
Track 01:   0 of 1660 MB written.dvdrecord: Input/output error. 
write_g1: scsi sendcmd: no error
CDB:  2A 00 00 0C F9 C6 00 00 1F 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 05 00 00 00 00 12 00 00 00 00 21 02 00 00
Sense Key: 0x5 Illegal Request, Segment 0
Sense Code: 0x21 Qual 0x02 (logical block address out of range) [No 
matching qualifier] Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 0.003s timeout 200s

write track data: error after 0 bytes
Sense Bytes: 70 00 00 00 00 00 00 12 00 00 00 00 00 00 00 00 00 00
Writing  time:    5.030s
Fixating...
WARNING: Some drives don't like fixation in dummy mode.
Fixating time:    0.002s
dvdrecord: fifo had 64 puts and 1 gets.
dvdrecord: fifo was 0 times empty and 0 times full, min fill was 100%.

Also in my case any help would be VERY appreciated.

Kevin wrote:

> Thus far, i cannot get this drive (LiteOn SOHW 1633S) to burn any DVDs
> using either dvdrecord (v0.2.1) or cdrecord patched (burning CDs actually
> works fine).
>
> I'm running Slackware 9.0.  I have used dvdrecord successfully on this
> machine before but with a Pioneer DVD-R unit.  I have bumped up the
> firmware on the LiteOn from BSOH to the latest BSOS, but that didn't change
> anything.  I am using Memorex DVD+R media.
>
> Command:
> dvdrecord dev=0,0,0 -dao ./test.raw
>
> The end result:
> dvdrecord: Input/output error. write_g1: scsi sendcmd: no error
> CDB:  2A 00 00 1D BF 36 00 00 1F 00
> status: 0x2 (CHECK CONDITION)
> Sense Bytes: 70 00 05 00 00 00 00 0A 00 00 00 00 21 02 00 00
> Sense Key: 0x5 Illegal Request, Segment 0
> Sense Code: 0x21 Qual 0x02 (logical block address out of range) [No
> matching qualifier] Fru 0x0 Sense flags: Blk 0 (not valid)  cmd finished
> after 0.003s timeout 200s write track data: error after 0 bytes
> Sense Bytes: 70 00 00 00 00 00 00 0A 00 00 00 00 00 00 00 00 00 00
>
> I have tried burning different image files and burning at different
> speeds (1x and 4x) all with the same results.
>
> Any help or ideas would be GREATLY appreciated.
> /KRM
>
>
>
> _______________________________________________
> Dvdrtools-users mailing list
> address@hidden
> http://lists.nongnu.org/mailman/listinfo/dvdrtools-users
>