Re: [Bayonne-devel] About the method of acquiring caller ID

[Dmitry Agafonov]

>To Mr.Dmitry
>
>Thank you for replying.
>
>Will you confirm the given content, and is it good?
>
>>1. Set answer on 2nd ring in bayonne.conf
>
>
>  As for this, is it good in the thing of changing "answer"
>  under [trunks] described in "bayonne.conf" as follows?
>
>  <before><after>
>  ;answer=1   ->  answer=2
>
You are right here.

>
>>2. Make sure your telco uses CallerID protocol compatible with your 
board.
>
>
>  Is here good in recognition of setting of "dialogic.cfg" it?
>  The setting of current "dialogic.cfg" is described as follows to 
make sure.
>------------------------------------------------------------------------------
>    [Genload - All Boards]
>    LogFile=genload.log
>    BusType=SCBus
>    SCBusClockMaster=AUTOMATIC
>    SCBusClockMasterSource=AUTOMATIC
>    PCMEncoding=ULAW
>    Country=JP
>    ParameterFile=JP_41J.prm
>
>    [Genload - PCI ID 0] /* D/41JCT-LS  */
>-------------------------------------------------------------------------------
>  Is it a thing that the line actually used confirms
>whether it is caller ID correspondence?
>
Default settings are include CallerID support for your board (and I do 
not know how to turn it off|on).
Configuration file is not sutable to find out what standard is used. I 
do not remember actual link, so
you have to search intel.com site for datasheet for D/41JCT-LS. And I 
beleave your phone line provider
has some technical support, try to call them to find out if callerid 
service is enabled...

These boards use FSK 1200bps data packet between 1st and 2nd ring as 
carrier for CallerID information,
this is an american standard and is also used in some other countries, 
sorry I do not know about Japan...
As for Russia - our standards are different, so internal callerid 
feature for analogue boards do not even works...

>
>I am sorry indeed on your precious time.
>It would be greatly appreciated when it is possible to reply again.
>
>My best regards.
>
>
>
>Dmitry Agafonov:
>
>>Tomoya Yoshida wrote:
>>
>>>Hi all
>>>
>>>Please teach the method of acquiring the caller ID at inbound.
>>>
>>>I am using the "D41JCT-LS" board.
>>>The line is an analog network of Japan.
>>>
>>>
>>First you can:
>>1. Set answer on 2nd ring in bayonne.conf
>>2. Make sure your telco uses CallerID protocol compatible with your 
board.
>>
>>>Middleware uses bayonne.
>>>The following sample scripts were made,
>>>and the acquisition of the caller ID at inbound was
>>>executed actually.
>>>----------------------------------------------------------------
>>><test.scr>
>>>answer.intercom
>>>
>>>   slog.info "1 %session.callerid
>>>   slog.info "2 %session.calledid
>>>   slog.info "3 %pstn.clid
>>>   slog.info "4 %pstn.dnid
>>>
>>>exit
>>>----------------------------------------------------------------
>>>However, all information becomes "UNKNOWN" as for the result.
>>>
>>>Are another some settings necessary to acquire caller ID?
>>>   For instance, "/etc/bayonne.conf", "/etc/bayonne.sched",
>>>   and "/usr/dialogic/cfg/dialogic.cfg", etc.
>>>
>>>Please teach the setting method by all means
>>>when succeeding in the acquisition of caller ID comes.
>>>
>>>There is no thing that it is not possible to acquire it
>>>because it is a line in Japan.
>>>
>>>Please my best regards.
>>>
>>>
>>>
>>>
>>
>>--
>>Dmitry
>>
>
>from:Tomoya Yoshida (address@hidden)
>
>


--
Dmitry