[Top][All Lists]
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [Discuss-gnuradio] No UHD Devices Found
From: |
Tobias Schmid |
Subject: |
Re: [Discuss-gnuradio] No UHD Devices Found |
Date: |
Wed, 28 Jul 2010 12:27:07 +0200 (CEST) |
Hello,
thanks for your quick answer.
I checked it and I think ists okay.
inupc33:/home/gnuradio/gnuradio/uhd/host/utils # route -n
Kernel IP Routentabelle
Ziel Router Genmask Flags
Metric Ref Use Iface
129.69.175.0 0.0.0.0 255.255.255.0 U 0 0
0 eth0
192.168.10.0 0.0.0.0 255.255.255.0 U 0 0
0 eth1
169.254.0.0 0.0.0.0 255.255.0.0 U 0
0 0 eth0
127.0.0.0 0.0.0.0 255.0.0.0 U 0
0 0 lo
0.0.0.0 129.69.175.254 0.0.0.0 UG 0
0 0 eth0
And in contrast to Luca I used the
ping -I eth1 192.168.10.2 -command to be sure that is use the right network
device.
Tobias
-----Ursprüngliche Nachricht-----
Von: Matthias Wilhelm <address@hidden>
Gesendet: 28.07.2010 11:30:50
An: address@hidden
Betreff: Re: [Discuss-gnuradio] No UHD Devices Found
>Hello,
>
>"destination host unreachable" indicates that the route is not set correctly.
>Try
>
># route add -net 192.168.10.0/24 dev eth1
>
>or check
>
># route -n
>
>to see if the routing is using the proper network devices.
>
>Matthias
>
>
>Am 28.07.2010 um 11:10 schrieb Tobias Schmid:
>
>> Hi,
>>
>> I've got exactly the same problem.
>> In my case the lights D and F are light up.
>>
>> The usrp2_card_burner_gui.py works correctly. I've checked that by flashing
>> the cards with the common firmware.
>> And that works fine.
>>
>> Tobias
>>
>> Am 15.07.2010 18:32, schrieb Josh Blum:
>>> Are the UHD images burned onto the sd card?
>>>
>>> http://code.ettus.com/redmine/ettus/projects/public/wiki/U2binaries#UHD-Firmware-and-FPGA-Images
>>>
>>>
>>> http://www.ettus.com/uhd_docs/manual/html/usrp2.html#load-the-images-onto-the-sd-card
>>>
>>>
>>> Are lights E and F light up on the front panel once powered up?
>>>
>>> -Josh
>>>
>>> On 07/15/2010 09:28 AM, Luca Pascale wrote:
>>>> Hi,
>>>> I have received two new USRP2 (rev 4) with a BasicRx DB. I connect the DB,
>>>> set the gbit lan so that :
>>>>
>>>> eth1 Link encap:Ethernet HWaddr 00:15:17:e6:86:56
>>>> inet addr:192.168.10.1 Bcast:192.168.10.255 Mask:255.255.255.0
>>>> inet6 addr: fe80::215:17ff:fee6:8656/64 Scope:Link
>>>> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
>>>> RX packets:0 errors:0 dropped:0 overruns:0 frame:0
>>>> TX packets:190 errors:0 dropped:0 overruns:0 carrier:0
>>>> collisions:0 txqueuelen:1000
>>>> RX bytes:0 (0.0 B) TX bytes:27244 (27.2 KB)
>>>> Memory:f3000000-f3020000
>>>>
>>>> I connect the USRP2 to the GBIT lan port and try:
>>>> ping 192.168.10.2
>>>>
>>>> PING 192.168.10.2 (192.168.10.2) 56(84) bytes of data.
>>>> From 192.168.10.1 icmp_seq=2 Destination Host Unreachable
>>>> From 192.168.10.1 icmp_seq=3 Destination Host Unreachable
>>>> From 192.168.10.1 icmp_seq=4 Destination Host Unreachable
>>>>
>>>> am I missing something ?
>>>>
>>>> (I have also builded UHD and tried uhd_find_devices...result: No UHD
>>>> Devices
>>>> Found )
>>>>
>>>> Any suggestions ?? (same behaviours on both uspr2)
>>>> thanks in advance Luca
>>>>
>>>>
>>>>
>>>>
>>>> _______________________________________________
>>>> Discuss-gnuradio mailing list
>>>> address@hidden
>>>> http://lists.gnu.org/mailman/listinfo/discuss-gnuradio
>>>
>>> _______________________________________________
>>> Discuss-gnuradio mailing list
>>> address@hidden
>>> http://lists.gnu.org/mailman/listinfo/discuss-gnuradio
>>>
>>
>>
>> _______________________________________________
>> Discuss-gnuradio mailing list
>> address@hidden
>> http://lists.gnu.org/mailman/listinfo/discuss-gnuradio
>
>
>_______________________________________________
>Discuss-gnuradio mailing list
>address@hidden
>http://lists.gnu.org/mailman/listinfo/discuss-gnuradio
___________________________________________________________
WEB.DE DSL ab 19,99 Euro/Monat. Bis zu 150,- Euro Startguthaben und
50,- Euro Geldprämie inklusive! https://freundschaftswerbung.web.de