[Qemu-ppc] [PULL 1/2] spapr: Reset CAS & IRQ subsystem after devices

[David Gibson]

This fixes a nasty regression in qemu-4.1 for the 'pseries' machine,
caused by the new "dual" interrupt controller model.  Specifically,
qemu can crash when used with KVM if a 'system_reset' is requested
while there's active I/O in the guest.

The problem is that in spapr_machine_reset() we:

1. Reset the CAS vector state
        spapr_ovec_cleanup(spapr->ov5_cas);

2. Reset all devices
        qemu_devices_reset()

3. Reset the irq subsystem
        spapr_irq_reset();

However (1) implicitly changes the interrupt delivery mode, because
whether we're using XICS or XIVE depends on the CAS state.  We don't
properly initialize the new irq mode until (3) though - in particular
setting up the KVM devices.

During (2), we can temporarily drop the BQL allowing some irqs to be
delivered which will go to an irq system that's not properly set up.

Specifically, if the previous guest was in (KVM) XIVE mode, the CAS
reset will put us back in XICS mode.  kvm_kernel_irqchip() still
returns true, because XIVE was using KVM, however XICs doesn't have
its KVM components intialized and kernel_xics_fd == -1.  When the irq
is delivered it goes via ics_kvm_set_irq() which assert()s that
kernel_xics_fd != -1.

This change addresses the problem by delaying the CAS reset until
after the devices reset.  The device reset should quiesce all the
devices so we won't get irqs delivered while we mess around with the
IRQ.  The CAS reset and irq re-initialize should also now be under the
same BQL critical section so nothing else should be able to interrupt
it either.

We also move the spapr_irq_msi_reset() used in one of the legacy irq
modes, since it logically makes sense at the same point as the
spapr_irq_reset() (it's essentially an equivalent operation for older
machine types).  Since we don't need to switch between different
interrupt controllers for those old machine types it shouldn't
actually be broken in those cases though.

Cc: Cédric Le Goater <address@hidden>

Fixes: b2e22477 "spapr: add a 'reset' method to the sPAPR IRQ backend"
Fixes: 13db0cd9 "spapr: introduce a new sPAPR IRQ backend supporting
                 XIVE and XICS"
Signed-off-by: David Gibson <address@hidden>
---
 hw/ppc/spapr.c | 24 ++++++++++++------------
 1 file changed, 12 insertions(+), 12 deletions(-)

diff --git a/hw/ppc/spapr.c b/hw/ppc/spapr.c
index 821f0d4a49..12ed4b065c 100644
--- a/hw/ppc/spapr.c
+++ b/hw/ppc/spapr.c
@@ -1726,6 +1726,18 @@ static void spapr_machine_reset(MachineState *machine)
         spapr_setup_hpt_and_vrma(spapr);
     }
 
+    /*
+     * NVLink2-connected GPU RAM needs to be placed on a separate NUMA node.
+     * We assign a new numa ID per GPU in spapr_pci_collect_nvgpu() which is
+     * called from vPHB reset handler so we initialize the counter here.
+     * If no NUMA is configured from the QEMU side, we start from 1 as GPU RAM
+     * must be equally distant from any other node.
+     * The final value of spapr->gpu_numa_id is going to be written to
+     * max-associativity-domains in spapr_build_fdt().
+     */
+    spapr->gpu_numa_id = MAX(1, nb_numa_nodes);
+    qemu_devices_reset();
+
     /*
      * If this reset wasn't generated by CAS, we should reset our
      * negotiated options and start from scratch
@@ -1741,18 +1753,6 @@ static void spapr_machine_reset(MachineState *machine)
         spapr_irq_msi_reset(spapr);
     }
 
-    /*
-     * NVLink2-connected GPU RAM needs to be placed on a separate NUMA node.
-     * We assign a new numa ID per GPU in spapr_pci_collect_nvgpu() which is
-     * called from vPHB reset handler so we initialize the counter here.
-     * If no NUMA is configured from the QEMU side, we start from 1 as GPU RAM
-     * must be equally distant from any other node.
-     * The final value of spapr->gpu_numa_id is going to be written to
-     * max-associativity-domains in spapr_build_fdt().
-     */
-    spapr->gpu_numa_id = MAX(1, nb_numa_nodes);
-    qemu_devices_reset();
-
     /*
      * This is fixing some of the default configuration of the XIVE
      * devices. To be called after the reset of the machine devices.
-- 
2.21.0