RE: Questions about CXL device (type 3 memory) hotplug

[Yuquan Wang]

On Mon, May 22, 2023 at 05:11:39PM -0700, Dan Williams wrote:
> Yasunori Gotou (Fujitsu) wrote:
[...]

Hi, all

There was some confusions about CXL device hotplug when I recently
tried to use Qemu to emulate CXL device hotplug and verify the relevant
functions of kernel.

> > Q1) Can PCIe hotplug driver detect and call CXL driver?

[...]

> 
> Yes.
> 
> The cxl_pci driver (drivers/cxl/pci.c) is just a typical PCI driver as
> far as the PCI hotplug driver is concerned. So add/remove events of a
> CXL card get turned into probe()/remove() events on the driver.
> 

1. Can we divide steps of CXL device hotplug into two parts(PCI hotplug & 
Memory Hotplug)?

PCI Hotplug: the same as the native PCIe hotplug, including initializing cxl.io,
             assigning PCIe BARs, allocating interrupts, etc. And the cxl_pci 
driver
                         is responsible for this part.

Memory Hotplug: focusing on enabling CXL memory including discovering and 
Configuring HDM,
                extracting NUMA info from device, notifying memory management, 
etc.

> > 
> > Q2) Can QEMU/KVM emulate CXL device hotplug?
> > 
> >    I heard that QEMU/KVM has PCIe device hotplug emulation, but I'm not sure
> >    it can hotplug CXL device.
> 
> It can, but as far as the driver is concerned you can achieve the same
> by:
> 
> echo $devname > /sys/bus/pci/drivers/cxl_pci/unbind
> 
> ...that exercises the same software flows as physical unplug.
>

2. What is the difference between "echo $devname > 
/sys/bus/pci/drivers/cxl_pci/unbind" and
"(qemu) device_del cxl-mem0" ?

According to the test, I found that "(qemu) device_del cxl-mem0" would directly
unplug the device and cause the interrupts on the cxl root port. It seems like 
this
operation would not only trigger cxl_pci driver but also pcieport driver.

The kernel dmesg is like below:

(qemu) device_del cxl-mem0
# dmesg
[  699.057907] pcieport 0000:0c:00.0: pciehp: pending interrupts 0x0001 from 
Slot Status
[  699.058929] pcieport 0000:0c:00.0: pciehp: Slot(0): Button press: will power 
off in 5 sec
[  699.059986] pcieport 0000:0c:00.0: pciehp: pending interrupts 0x0010 from 
Slot Status
[  699.060099] pcieport 0000:0c:00.0: pciehp: pciehp_set_indicators: SLOTCTRL 
90 write cmd 2c0

Then I also tried "echo $devname > /sys/bus/pci/drivers/cxl_pci/unbind"
to check the behaviour of kernel. The kernel dmesg is like below:

# echo 0000:0d:00.0 > /sys/bus/pci/drivers/cxl_pci/unbind
# dmesg
[70387.978931] cxl_pci 0000:0d:00.0: vgaarb: pci_notify
[70388.021476] cxl_mem mem0: disconnect mem0 from port1
[70388.033099] pci 0000:0d:00.0: vgaarb: pci_notify

It seems like this operation would just unbind the cxl_pci driver from the cxl 
device.

Is my understanding about these two method correct?

3) Can I just use "ndctl/test/cxl-topology.sh" to test the cxl hotplug 
functions of kernel?

   IIUC, cxl-topology.sh would utilize cxl_test (tools/testing/cxl) which is 
for regression
   testing the kernel-user ABI.

PS: My qemu command line:
qemu-system-x86_64 \
-M q35,nvdimm=on,cxl=on \
-m 4G \
-smp 4 \
-object memory-backend-ram,size=2G,id=mem0 \
-numa node,nodeid=0,cpus=0-1,memdev=mem0 \
-object memory-backend-ram,size=2G,id=mem1 \
-numa node,nodeid=1,cpus=2-3,memdev=mem1 \
-object memory-backend-ram,size=256M,id=cxl-mem0 \
-device pxb-cxl,bus_nr=12,bus=pcie.0,id=cxl.1 \
-device cxl-rp,port=0,bus=cxl.1,id=root_port0,chassis=0,slot=0 \
-device cxl-type3,bus=root_port0,volatile-memdev=cxl-mem0,id=cxl-mem0 \
-M 
cxl-fmw.0.targets.0=cxl.1,cxl-fmw.0.size=4G,cxl-fmw.0.interleave-granularity=4k 
\
-hda ../disk/ubuntu_x86_test_new.qcow2 \
-nographic \

Qemu version: 8.2.50, the lastest commit of branch cxl-2024-03-05 in 
"https://gitlab.com/jic23/qemu";
Kernel version: 6.8.0-rc6

Many thanks
Yuquan