qemu-devel
[Top][All Lists]
Advanced

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

[Bug 1030807] Re: PCI host bridge should ignore 1- and 2-byte I/O access


From: Launchpad Bug Tracker
Subject: [Bug 1030807] Re: PCI host bridge should ignore 1- and 2-byte I/O accesses
Date: Wed, 07 Oct 2020 04:17:22 -0000

[Expired for QEMU because there has been no activity for 60 days.]

** Changed in: qemu
       Status: Incomplete => Expired

-- 
You received this bug notification because you are a member of qemu-
devel-ml, which is subscribed to QEMU.
https://bugs.launchpad.net/bugs/1030807

Title:
  PCI host bridge should ignore 1- and 2-byte I/O accesses

Status in QEMU:
  Expired

Bug description:
  In PCI there are two IO modes. Deprecated Mode2 that uses single byte IO and 
Mode1 that uses 4byte IO.
  According to the spec a host bridge that supports Mode1 should ignore all IO 
that is not 4bytes.

  > Anytime a host bridge sees a full DWORD I/O write from the host to
  > CONFIG_ADDRESS, the bridge must latch the data into its CONFIG_ADDRESS
  > register. On full DWORD I/O reads to CONFIG_ADDRESS, the bridge must return 
the
  > data in CONFIG_ADDRESS. Any other types of accesses to this address 
(non-DWORD)
  > have no effect on CONFIG_ADDRESS and are executed as normal I/O 
transactions on
  > the PCI bus. Therefore, the only I/O Space consumed by this register is a 
DWORD at the
  > given address. I/O devices that share the same address but use BYTE or WORD 
registers
  > are not affected because their transactions will pass through the host 
bridge unchanged.

  In qemu the host bridge will accept 1-, 2-, and 4-byte reads/writes.
  That breakes plan9 guests that do not use the bios to access the PCI
  config space.

  have a look at:
  http://code.google.com/p/plan9front/source/browse/sys/src/9/pc/pci.c

  In Lines 960-967 the check for PCI Mode1 is done. This check assumes that the 
4-byte write at line 961 succeeds and the single byte write at 962 is ignored.
  On qemu line 962 will not be ignored and the test in line 963 will fail.
  The plan9 kernel will fall back to Mode2 which does not work.
  The result is that the guest will not see any PCI devices.

  I do not really have an image that you guys could quickly check this with, 
but i could prepare one if need be.
  An easy way to reproduce this in linux would be to stick an outb between 
those two lines from pci_check_type1(void).

  > outl(0x80000000, 0xCF8);
  + outb0x01, 0xcfb);
  > if (inl(0xCF8) == 0x80000000 && pci_sanity_check(&pci_direct_conf1)) {

  I did not try this but i guess on real hardware the linux kernel would
  still work while it would not work anymore on qemu.

  I tried to come up with a patch but did not find a quick solution. I
  found that in hw/piic_pci.c sysbus_add_io is used which will register
  read/write functions for 1, 2, and 4 bytes. This is done in ioport.c
  ioport_register. I guess if i provided a patch you guys might not like
  it :). So i figured i should report the bug, let me know if you need
  any additional information.

To manage notifications about this bug go to:
https://bugs.launchpad.net/qemu/+bug/1030807/+subscriptions



reply via email to

[Prev in Thread] Current Thread [Next in Thread]