[PATCH 1/2] Kconfig: Add I2C_DEVICES device group

[Peter Maydell]

Currently there is no way for a board model's Kconfig stanza to
say "I have an i2c bus which the user can plug an i2c device into,
build all the free-standing i2c devices". The Kconfig mechanism
for this is the "device group". Add an I2C_DEVICES group along
the same lines as the existing PCI_DEVICES. Simple free-standing
i2c devices which a user might plausibly want to be able to
plug in on the QEMU commandline should have
   default y if I2C_DEVICES
and board models which have an i2c bus that is user-accessible
should use
   imply I2C_DEVICES
to cause those pluggable devices to be built.

In this commit we mark only a fairly conservative set of i2c devices
as belonging to the I2C_DEVICES group: the simple sensors and RTCs
(not including PMBus devices or devices which need GPIO lines to be
connected).

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
---
Feel free to suggest other i2c devices that should be marked
as in the group; as I say, I erred on the side of not putting
devices in the group.
---
 docs/devel/kconfig.rst | 8 ++++++--
 hw/i2c/Kconfig         | 5 +++++
 hw/rtc/Kconfig         | 2 ++
 hw/sensor/Kconfig      | 5 +++++
 4 files changed, 18 insertions(+), 2 deletions(-)

diff --git a/docs/devel/kconfig.rst b/docs/devel/kconfig.rst
index a1cdbec7512..aa5042f1569 100644
--- a/docs/devel/kconfig.rst
+++ b/docs/devel/kconfig.rst
@@ -192,11 +192,15 @@ declares its dependencies in different ways:
   no directive and are not used in the Makefile either; they only appear
   as conditions for ``default y`` directives.
 
-  QEMU currently has two device groups, ``PCI_DEVICES`` and
-  ``TEST_DEVICES``.  PCI devices usually have a ``default y if
+  QEMU currently has three device groups, ``PCI_DEVICES``, ``I2C_DEVICES``,
+  and ``TEST_DEVICES``.  PCI devices usually have a ``default y if
   PCI_DEVICES`` directive rather than just ``default y``.  This lets
   some boards (notably s390) easily support a subset of PCI devices,
   for example only VFIO (passthrough) and virtio-pci devices.
+  ``I2C_DEVICES`` is similar to ``PCI_DEVICES``. It contains i2c devices
+  that users might reasonably want to plug in to an i2c bus on any
+  board (and not ones which are very board-specific or that need
+  to be wired up in a way that can't be done on the command line).
   ``TEST_DEVICES`` instead is used for devices that are rarely used on
   production virtual machines, but provide useful hooks to test QEMU
   or KVM.
diff --git a/hw/i2c/Kconfig b/hw/i2c/Kconfig
index 8217cb50411..9bb8870517f 100644
--- a/hw/i2c/Kconfig
+++ b/hw/i2c/Kconfig
@@ -1,6 +1,11 @@
 config I2C
     bool
 
+config I2C_DEVICES
+    # Device group for i2c devices which can reasonably be user-plugged
+    # to any board's i2c bus
+    bool
+
 config SMBUS
     bool
     select I2C
diff --git a/hw/rtc/Kconfig b/hw/rtc/Kconfig
index f06e133b8a2..730c272bc54 100644
--- a/hw/rtc/Kconfig
+++ b/hw/rtc/Kconfig
@@ -1,10 +1,12 @@
 config DS1338
     bool
     depends on I2C
+    default y if I2C_DEVICES
 
 config M41T80
     bool
     depends on I2C
+    default y if I2C_DEVICES
 
 config M48T59
     bool
diff --git a/hw/sensor/Kconfig b/hw/sensor/Kconfig
index b317f91b7b4..215944decc7 100644
--- a/hw/sensor/Kconfig
+++ b/hw/sensor/Kconfig
@@ -1,18 +1,22 @@
 config TMP105
     bool
     depends on I2C
+    default y if I2C_DEVICES
 
 config TMP421
     bool
     depends on I2C
+    default y if I2C_DEVICES
 
 config DPS310
     bool
     depends on I2C
+    default y if I2C_DEVICES
 
 config EMC141X
     bool
     depends on I2C
+    default y if I2C_DEVICES
 
 config ADM1272
     bool
@@ -25,3 +29,4 @@ config MAX34451
 config LSM303DLHC_MAG
     bool
     depends on I2C
+    default y if I2C_DEVICES
-- 
2.25.1