[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [Qemu-arm] [PATCH v9 1/2] hw/arm: Add arm SBSA reference machine, sk
From: |
Peter Maydell |
Subject: |
Re: [Qemu-arm] [PATCH v9 1/2] hw/arm: Add arm SBSA reference machine, skeleton part |
Date: |
Mon, 1 Jul 2019 15:18:52 +0100 |
On Sun, 30 Jun 2019 at 11:21, Hongbo Zhang <address@hidden> wrote:
>
> For the Aarch64, there is one machine 'virt', it is primarily meant to
> run on KVM and execute virtualization workloads, but we need an
> environment as faithful as possible to physical hardware, for supporting
> firmware and OS development for pysical Aarch64 machines.
>
> This patch introduces new machine type 'sbsa-ref' with main features:
> - Based on 'virt' machine type.
> - A new memory map.
> - CPU type cortex-a57.
> - EL2 and EL3 are enabled.
> - GIC version 3.
> - System bus AHCI controller.
> - System bus EHCI controller.
> - CDROM and hard disc on AHCI bus.
> - E1000E ethernet card on PCIE bus.
> - VGA display adaptor on PCIE bus.
> - No virtio deivces.
> - No fw_cfg device.
> - No ACPI table supplied.
> - Only minimal device tree nodes.
>
> Arm Trusted Firmware and UEFI porting to this are done accordingly, and
> it should supply ACPI tables to load OS, the minimal device tree nodes
> supplied from this platform are only to pass the dynamic info reflecting
> command line input to firmware, not for loading OS.
>
> To make the review easier, this task is split into two patches, the
> fundamental sceleton part and the peripheral devices part, this patch is
> the first part.
>
> Signed-off-by: Hongbo Zhang <address@hidden>
> ---
> default-configs/arm-softmmu.mak | 1 +
> hw/arm/Kconfig | 16 +++
> hw/arm/Makefile.objs | 1 +
> hw/arm/sbsa-ref.c | 281
> ++++++++++++++++++++++++++++++++++++++++
> 4 files changed, 299 insertions(+)
> create mode 100644 hw/arm/sbsa-ref.c
>
> diff --git a/default-configs/arm-softmmu.mak b/default-configs/arm-softmmu.mak
> index 1f2e0e7..f9fdb73 100644
> --- a/default-configs/arm-softmmu.mak
> +++ b/default-configs/arm-softmmu.mak
> @@ -19,6 +19,7 @@ CONFIG_SX1=y
> CONFIG_NSERIES=y
> CONFIG_STELLARIS=y
> CONFIG_REALVIEW=y
> +CONFIG_SBSA_REF=y
> CONFIG_VERSATILE=y
> CONFIG_VEXPRESS=y
> CONFIG_ZYNQ=y
Adding CONFIG_SBSA_REF=y here is what makes the board
model available for the 32-bit-only qemu-system-arm.
If you put it in aarch64-softmmu.mak instead it will
be correctly restricted to the 64-bit binary.
> diff --git a/hw/arm/Kconfig b/hw/arm/Kconfig
> index 9aced9d..18e47b2 100644
> --- a/hw/arm/Kconfig
> +++ b/hw/arm/Kconfig
> @@ -184,6 +184,22 @@ config REALVIEW
> select DS1338 # I2C RTC+NVRAM
> select USB_OHCI
>
> +config SBSA_REF
> + bool
> + imply PCI_DEVICES
> + select A15MPCORE
This looks like a leftover from the virt config?
> + select AHCI
> + select ARM_SMMUV3
> + select GPIO_KEY
> + select PCI_EXPRESS
> + select PCI_EXPRESS_GENERIC_BRIDGE
> + select PFLASH_CFI01
> + select PL011 # UART
> + select PL031 # RTC
> + select PL061 # GPIO
> + select PLATFORM_BUS
I don't think you use the platform-bus either, do you?
> + select USB_EHCI_SYSBUS
> +
> config SABRELITE
> bool
> select FSL_IMX6
thanks
-- PMM
- Re: [Qemu-arm] [PATCH v9 1/2] hw/arm: Add arm SBSA reference machine, skeleton part,
Peter Maydell <=