paparazzi-devel
[Top][All Lists]
Advanced

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Paparazzi-devel] can't arm the motors


From: evan igor
Subject: Re: [Paparazzi-devel] can't arm the motors
Date: Sun, 9 Mar 2014 17:55:01 +0200

Hi,

any notes for those problems :)


On Sun, Mar 9, 2014 at 3:45 AM, evan igor <address@hidden> wrote:
I used FTDI with paparazzi and it showed the following errors in GCS in the attached pictures
any suggestions i appreciate in advance.





Inline image 3Inline image 4Inline image 5Inline image 6Inline image 7Inline image 8

Inline image 1


On Thu, Mar 6, 2014 at 11:40 PM, evan igor <address@hidden> wrote:
thanks for this great idea idea actually ididn't think in before.

i'll try it thanks Felix.


On Thu, Mar 6, 2014 at 11:37 PM, Felix Ruess <address@hidden> wrote:
Then use that instead of the 3dr modems and check the status in GCS/messages...


On Thu, Mar 6, 2014 at 10:36 PM, evan igor <address@hidden> wrote:
i have ftdi cable.


On Thu, Mar 6, 2014 at 11:29 PM, Felix Ruess <address@hidden> wrote:
Well, it's a bit hard to help out without knowing what's going on....
Do you have a seria<l->usb cable (e.g. FTDI cable) or a BMP or JTAG which also has that?
transparent_usb is only implemented for LPC21xx based autopilots...


On Thu, Mar 6, 2014 at 10:21 PM, evan igor <address@hidden> wrote:
for sorry Felix , i have another trouble with telemetry as i'm using 3dr modem and set it to raw data and disable mavlink protocol for and no telemetry appear is there any way to check.
i didn't try transparent_usb should it help to get telemetry through usb cable.
thanks


On Thu, Mar 6, 2014 at 11:18 PM, Felix Ruess <address@hidden> wrote:
Are your motors armed? Did you check in GCS if the throttle indicator goes to green? You can also check the ap_motors_on in the ROTORCRAFT_STATUS message....


On Thu, Mar 6, 2014 at 10:15 PM, AFISH <address@hidden> wrote:
Try to low throttle, maybe you need trim to the lowest position.

Sent from Mailbox for iPhone


On Thu, Mar 6, 2014 at 4:11 PM, evan igor <address@hidden> wrote:

Hi everyone in this great community,

i got paparazzi lisa/m and i connected the spectrum satellite receiver to UART 1/5.
connect the v_in to 5 volt from speed controller and its GND to the GND of speed controller and connect simply one motor for testing after powering it from external lipo 6 cell. make the binding procedure then make the transmitter in the position low throttle full yaw.  


but 
<B04.gif>
 no action to the motor.

any advices.

thanks


_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel



_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel



_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel



_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel



_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel



_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel





reply via email to

[Prev in Thread] Current Thread [Next in Thread]