Re: [Paparazzi-devel] YNT: Rotate reference frame - Lisa/M 2.0 Aspirin 2.2 - mounting the IMU correctly

[Tim Sindle]

Hi Markus, 

I think you can just add the following single line to the airframe file for this setup.

<define name="LISA_M_LONGITUDINAL_X"/>

As an example...

<firmware name="fixedwing">

    <target name="ap" board="lisa_m_2.0">

      <define name="LISA_M_LONGITUDINAL_X"/>

...

Cheers, 

Tim

On 10 September 2013 06:45, Markus Bina <address@hidden> wrote:

Hi Refik,

Just three lines? That's really great! :-)
Thanks!

Cheers,
  Markus

Am 09.09.2013 22:18, schrieb Refik Sever:

Hi Markus,

You can edit these parameters:

<section name="IMU" prefix="IMU_">
     <define name="BODY_TO_IMU_PHI"   value="-0.93" unit="deg"/>
     <define name="BODY_TO_IMU_THETA" value="10.71" unit="deg"/>
     <define name="BODY_TO_IMU_PSI"   value="0." unit="deg"/>
   </section>

Then, check the PFD screen.
Refik

________________________________________
Kimden: Markus Bina [address@hidden] adına paparazzi-devel-bounces+refiksever=akdeniz.edu.tr@nongnu.org [paparazzi-devel-bounces+refiksever=akdeniz.edu.tr@nongnu.org]
Gönderildi: 09 Eylül 2013 Pazartesi 23:11
Kime: address@hidden
Konu: [Paparazzi-devel] Rotate reference frame - Lisa/M 2.0 Aspirin 2.2 - mounting the IMU correctly

Hi all.

A few days ago I finished assembling all the hardware for my first
"fixed wing"-configuration.
Since I'm still a RC/Paparazzi beginner I figured to start by using the
"Bixler"-airframe, which I can fly reasonably well without any
autopilot, for my first setup.

Basically, I would like to mount the autopilot (Lisa/M) with the long
side parallel to the fuselage, i.e. not like this
http://paparazzi.enac.fr/wiki/File:Bixler_Cockpit.jpg.
Thus I'd not have to make any permanent changes to my airframe (the
autopilot sits on a piece of acrylic (PMMA) in the CM fixed by velcro;
thus removeable)
and there wouldn't be any wires hanging out of the fuselage.
This would - imho - also ease the wiring.

How do I rotate the IMU/Autopilot reference frame in the airframe
configuration (XML) consistently for/in all subsystems
(imu,ahrs,controller,etc.)?
To mount the Lisa/M board with its long side parallel to the fuselage I
figured, one needs to swap X and Y axis and invert the Y axis.

Hardware:
*) Airframe: Bixler  - http://paparazzi.enac.fr/wiki/Bixler
*) Board: Lisa/M v2.0 with Aspirin v2.2 from Transition Robotics
*) GPS: ublox
*) Telemetry: xbee
*) Radio: Spektrum (9645)

Sorry, in case my question is somewhat basic.

Thanks.

Cheers,
      Markus

_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel

_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel

_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel