Re: [Paparazzi-devel] New Autopilot hardware for 16 Euros

[Eduardo lavratti]

HUmmm nice to hear about PTH problem.
I not use this regulator on my boards.
I use an "ADAPTATION" jejejej
I ever use a external BEC.

when i assembled my first twog the PTH was burn after a short circuit then i never used this module.

BTW ... i found my first attempt to run a rotorcraft code on lisa_m.
its an adaptation using UNIVERSAL stm32 OLIMEX BOARD and tons of cables.

it worked but i used only 4 times. and only for tests.

---

Date: Tue, 27 Nov 2012 22:33:09 +0100
From: address@hidden
To: address@hidden
Subject: Re: [Paparazzi-devel] New Autopilot hardware for 16 Euros

Thank your for the answer.
My question was more related to the possibility to do it !
It is good to hear the word "Reliability" :) some months ago I tried to collect informations about AP boards reliability ! because I had bad experience with some PTH08080WAH ship. It would be nice it there is a statistical study to analyse the path of failure of the AP ! 

Imed LIMAIEM
address@hidden

On Tue, Nov 27, 2012 at 10:16 PM, Eduardo lavratti <address@hidden> wrote:

Reliability.

Some time ago i do exactly what you say !
The problem is .. "its adaptation" ...

lisa_m is not so much expensive.
I live in Brasil, so here, the price is 4x the real one and i have 2 lisa board and some twog.

Way? because i not want to use an adapted hardware on my planes and rotorcrafts.

for adaptation you can use and MULTI-WII ! its cheap !

---

Date: Tue, 27 Nov 2012 22:08:16 +0100

From: address@hidden
To: address@hidden
Subject: Re: [Paparazzi-devel] New Autopilot hardware for 16 Euros

I have little know how in Electronics and some good skills in programming.

What I can't figure out is that since we have the same micro-controller as the one used for LISA board and the same free connectors and assuming that we can add resistor, capacitor where in some places ... why can't we load the code in the micro-controller ?

am I missing something ?

Imed LIMAIEM
address@hidden

On Mon, Nov 26, 2012 at 12:34 AM, Eduardo lavratti <address@hidden> wrote:

Its complex ...
you have know how in electronics and C programming ?

I dont think the cheap universal board with processor and IMU are good to use as autopilot.

---

Date: Sun, 25 Nov 2012 20:45:17 +0100
From: address@hidden
To: address@hidden
Subject: Re: [Paparazzi-devel] New Autopilot hardware for 16 Euros

since LISA/M has the same processor the code should be easy to be loaded in this ship no ?

the only job to make is the get the right interface with GPS, IMU and the TX/RX ?

or I am missing something more complex ?



Imed LIMAIEM
address@hidden

On Tue, Nov 13, 2012 at 8:47 PM, Prof. Dr.-Ing. Heinrich Warmers <address@hidden> wrote:

Hi,
a new autopilot hardware for only 16 Euros ?
http://www.watterott.com/de/STM32F3DISCOVERY
How is the first to port paparazzi on it?

Regards

Heinrich


_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel

_______________________________________________ Paparazzi-devel mailing list address@hidden https://lists.nongnu.org/mailman/listinfo/paparazzi-devel

_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel

_______________________________________________ Paparazzi-devel mailing list address@hidden https://lists.nongnu.org/mailman/listinfo/paparazzi-devel

_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel

_______________________________________________ Paparazzi-devel mailing list address@hidden https://lists.nongnu.org/mailman/listinfo/paparazzi-devel