Re: [Paparazzi-devel] airframe configuration?

[hu zhangli]

>>>You can watch the values in the telemetry PPM for raw values and RC for 
>>>calibrated values.
please tell me wiki page. thanks

we should not develop so many hardware models, just one or two models
are enough.

then algorithm development will emphasize on these hardware modes.

just my suggestion.

On Fri, Sep 28, 2012 at 5:09 PM, Christophe De Wagter
<address@hidden> wrote:
> You can watch the values in the telemetry PPM for raw values and RC for
> calibrated values.
>
> I agree about the GUI. Paparazzi has so far focused on technology more than
> on users but this is changing. There is already an issue-report for this.
>
> -Christophe
>
>
>
>
> On Fri, Sep 28, 2012 at 11:04 AM, hu zhangli <address@hidden> wrote:
>>
>> but we should know about the acutal val ,then fill in the xml.
>>
>> firstly how to get the RC val , maybe GUI is good sensitive to teach
>> user . for example the GUI could show the RC throlle, yaw. range when
>> RC is operated by user.
>>
>> Openpilot support such feature.
>>
>>
>> On Fri, Sep 28, 2012 at 5:00 PM, Christophe De Wagter
>> <address@hidden> wrote:
>> > http://paparazzi.enac.fr/wiki/Paparazzi_Center
>> >
>> > the radio file defines the ppm signals of your receiver.
>> >
>> > the airframe file defines the servo deflections
>> >
>> > -Christophe
>> >
>> >
>> >
>> >
>> > On Fri, Sep 28, 2012 at 10:52 AM, hu zhangli <address@hidden>
>> > wrote:
>> >>
>> >> for example if we choose ppm, how to config the related channels and
>> >> threshhold value setting max ...min...
>> >>
>> >> On Fri, Sep 28, 2012 at 4:09 PM, Christophe De Wagter
>> >> <address@hidden> wrote:
>> >> > Unfortunately that guide is quite outdated. Several things still
>> >> > apply
>> >> > but
>> >> > not the makefile part.
>> >> >
>> >> > There is no more need for Makfile in your airframe. You can configure
>> >> > the
>> >> > autpilot using firmware, board and subsystems blocks.
>> >> >
>> >> > Look at: http://paparazzi.enac.fr/wiki/Airframe_Configuration
>> >> >
>> >> > and in ./conf/airframes/examples for something that matches your
>> >> > hardware
>> >> >
>> >> > -Christophe
>> >> >
>> >> >
>> >> >
>> >> > On Thu, Sep 27, 2012 at 2:06 PM, iman shirdareh
>> >> > <address@hidden>
>> >> > wrote:
>> >> >>
>> >> >> Hi
>> >> >>
>> >> >> I have some problem with airframe configuration, I'm following this
>> >> >> guid:http://www.rcgroups.com/forums/showthread.php?t=1000937
>> >> >>
>> >> >> but I can't find funjet1.XML file and there isn't any
>> >> >>
>> >> >>  <makefile>
>> >> >> CONFIG = \"tiny_2_1.h\"
>> >> >>
>> >> >>
>> >> >> in other example file, to change that?!
>> >> >>
>> >> >> I want to use my autopilot with Cessna 182 , Is there any similar
>> >> >> airframe
>> >> >> file to use?
>> >> >>
>> >> >>
>> >> >>
>> >> >> Thanks a lot..........Iman
>> >> >>
>> >> >>
>> >> >> _______________________________________________
>> >> >> Paparazzi-devel mailing list
>> >> >> address@hidden
>> >> >> https://lists.nongnu.org/mailman/listinfo/paparazzi-devel
>> >> >>
>> >> >
>> >> >
>> >> > _______________________________________________
>> >> > Paparazzi-devel mailing list
>> >> > address@hidden
>> >> > https://lists.nongnu.org/mailman/listinfo/paparazzi-devel
>> >> >
>> >>
>> >> _______________________________________________
>> >> Paparazzi-devel mailing list
>> >> address@hidden
>> >> https://lists.nongnu.org/mailman/listinfo/paparazzi-devel
>> >
>> >
>> >
>> > _______________________________________________
>> > Paparazzi-devel mailing list
>> > address@hidden
>> > https://lists.nongnu.org/mailman/listinfo/paparazzi-devel
>> >
>>
>> _______________________________________________
>> Paparazzi-devel mailing list
>> address@hidden
>> https://lists.nongnu.org/mailman/listinfo/paparazzi-devel
>
>
>
> _______________________________________________
> Paparazzi-devel mailing list
> address@hidden
> https://lists.nongnu.org/mailman/listinfo/paparazzi-devel
>