On Mon, Jan 2, 2012 at 10:37 PM, Luke Barnett <
address@hidden> wrote:
> I finally have tracked down the source of the problem. It would seem that
> periodically the data in the rx buffer gets offset by one, i.e. it starts at
> accel_rx_buf[2] instead of accel_rx_buf[1]. The strange thing is that this
> does not occur if I disable the magnetometers and read gyros and accels
> only. What I did to fix the issue is to call adxl345_clear_rx_buf() at the
> beginning of adxl_start_reading_data() (both functions are in
> stm32/mcu_periph/imu_aspirin_arch.c).
>
> With the modified code I have run it for several hours without any issues so
> it seems to work. I find it a little strange that no-one else has come
> across this same problem, which makes me worry that there is perhaps
> something else wrong specific to my hardware?
>
> Does anyone see any issues with the code changes I made? My experience with
> embedded programming is limited to say the least, so I'd appreciate it if
> anyone has any advice on this.
>
> Thanks
> Luke
>
>
>
> On Thu, Dec 22, 2011 at 11:15 PM, Cédric Marzer <
address@hidden> wrote:
>>
>> It might be a stupid idea and you probably considered that already, but
>> who knows : " the time to failure was shorter each time" = I would check the
>> power supply…
>>
>>
>>
>> De : paparazzi-devel-bounces+spam1=
address@hidden
>> [mailto:
paparazzi-devel-bounces+spam1=
address@hidden] De la part de
>> Luke Barnett
>> Envoyé : jeudi, 22. décembre 2011 10:31
>> À :
address@hidden
>> Objet : Re: [Paparazzi-devel] LisaL/Aspirin IMU Issues
>>
>>
>>
>> Hi Heinrich,
>>
>>
>>
>> Thanks for the reply. The motors were not running, the board was actually
>> removed from the quadcopter and sitting on my desk. During the whole time it
>> was not touched or moved so I would expect minimal vibrations during this
>> time. Interestingly, over three successive times, (i unplugged the board for
>> 10 seconds, then powered it up again after each time) the time to failure
>> was shorter each time. This leads me to think it may be a failure related to
>> temperature, however, when looking at it today running the test_imu_aspirin
>> program it read incorrectly from the start. So not really sure what is going
>> on.
>>
>>
>>
>> Regards
>>
>> Luke
>>
>>
>>
>> Date: Tue, 20 Dec 2011 14:09:51 +0100
>> From: "Prof. Dr.-Ing. Heinrich Warmers" <
address@hidden>
>> To:
address@hidden
>> Subject: Re: [Paparazzi-devel] LisaL/Aspirin IMU Issues
>> Message-ID: <
address@hidden>
>> Content-Type: text/plain; charset="us-ascii"; Format="flowed"
>>
>> Hello Banett,
>> some Questions:
>> Where the motor ruining? Then 5 to 20% full scale vibration is normal.
>> Is this a temperature problem ? Test it with cooling and hot air.
>> Sometimes the plastic of the mens has large humidity and this results
>> in contact problems by the soldering and destroy the chips.
>> Regards
>> Heinrich
>>
>> Luke Barnett schrieb:
>>
>> > Hello Everyone,
>> >
>> > I'm new to paparazzi and have been trying to get a quadcopter with
>> > Lisa/L and Aspirin IMU working over the last few months. However, I
>> > have noticed that after a period of time that I the quadcopter would
>> > seemingly lose orientation. For example the pfd would suddenly change
>> > orientation even when the quadrotor was on the ground. Luckily this
>> > has only happened a few times whilst actually flying.
>> >
>> > I have been benchtesting the setup out of the airframe and have been
>> > able to replicate the issue quite easily by just leaving running on
>> > the bench. After a period of time (so far between 8 and 14 minutes run
>> > time) it occurs again and what I have notices is that the raw
>> > accelerometer readings go haywire around the same time. Prior to this
>> > everything seems to be behaving normally. I've attached a screenshot
>> > of the logs to illustrate what is happening.
>> >
>> > Does anyone have any ideas what may be causing this? Any help would
>> > be appreciated.
>> >
>> > Thanks and Regards
>> > Luke
>> >
>> >
>> >
>> > ------------------------------------------------------------------------
>> >
>> >------------------------------------------------------------------------
>> >
>> >_______________________________________________
>> >Paparazzi-devel mailing list
>> >
address@hidden
>> >
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel
>> >
>> >
>> -------------- next part --------------
>> An HTML attachment was scrubbed...
>> URL:
>> <
http://lists.nongnu.org/archive/html/paparazzi-devel/attachments/20111220/3830c660/attachment.html>
>> -------------- next part --------------
>> A non-text attachment was scrubbed...
>> Name: not available
>> Type: image/png
>> Size: 33210 bytes
>> Desc: not available
>> URL:
>> <
http://lists.nongnu.org/archive/html/paparazzi-devel/attachments/20111220/3830c660/attachment.png>
>>
>> ------------------------------
>>
>>
>> _______________________________________________
>> Paparazzi-devel mailing list
>>
address@hidden
>>
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel
>>
>
>
> _______________________________________________
> Paparazzi-devel mailing list
>
address@hidden
>
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel
>
_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel