I dont know why, but now it doesn' t work no longer. The ground modem receive datas but GCS has a blank screen. I doesn' t change nothing
While compiling i had a warning: subsystems/imu/imu_aspirin.c:10:warning 'configure_mag' declared 'static' but never defined
Can anyonr help me?
Best regards.
Jochen
My airframe file:
<!DOCTYPE airframe SYSTEM "../../airframe.dtd">
<!--
Lisa/L + Aspirin + XBee
-->
<airframe name="Maja">
<servos>
<servo name="THROTTLE" no="0" min="1000" neutral="1000" max="2000"/>
<servo name="AILERON_LEFT" no="1" min="1000" neutral="1500" max="2000"/>
<servo name="AILERON_RIGHT" no="2" min="2000" neutral="1500" max="1000"/>
<servo name="ELEVATOR" no="3" min="2000" neutral="1500" max="1000"/>
<servo name="RUDDER" no="4" min="1100" neutral="1500" max="1900"/>
</servos>
<commands>
<axis name="THROTTLE" failsafe_value="0"/>
<axis name="ROLL" failsafe_value="0"/>
<axis name="PITCH" failsafe_value="0"/>
<axis name="BRAKE" failsafe_value="0"/> <!-- both elerons up as butterfly brake ? -->
</commands>
<rc_commands>
<set command="THROTTLE" value="@THROTTLE"/>
<set command="ROLL" value="@ROLL"/>
<set command="PITCH" value="@PITCH"/>
<set command="BRAKE" value="@YAW"/>
</rc_commands>
<command_laws>
<set servo="AILERON_LEFT" value="@ROLL"/>
<set servo="AILERON_RIGHT" value="@ROLL"/>
<set servo="THROTTLE" value="@THROTTLE"/>
<set servo="ELEVATOR" value="@PITCH"/>
</command_laws>
<!-- Local magnetic field -->
<section name="AHRS" prefix="AHRS_" >
<define name="H_X" value="0.51562740288882" />
<define name="H_Y" value="-0.05707735220832" />
<define name="H_Z" value="0.85490967783446" />
</section>
<section name="IMU" prefix="IMU_">
<!-- Calibration Neutral -->
<define name="GYRO_P_NEUTRAL" value="0"/>
<define name="GYRO_Q_NEUTRAL" value="0"/>
<define name="GYRO_R_NEUTRAL" value="0"/>
<!-- SENS = 14.375 LSB/(deg/sec) * 57.6 deg/rad = 828 LSB/rad/sec / 12bit FRAC: 4096 / 828 -->
<define name="GYRO_P_SENS" value="4.947" integer="16"/>
<define name="GYRO_Q_SENS" value="4.947" integer="16"/>
<define name="GYRO_R_SENS" value="4.947" integer="16"/>
<define name="GYRO_P_Q" value="0."/>
<define name="GYRO_P_R" value="0"/>
<define name="GYRO_Q_P" value="0."/>
<define name="GYRO_Q_R" value="0."/>
<define name="GYRO_R_P" value="0."/>
<define name="GYRO_R_Q" value="0."/>
<define name="GYRO_P_SIGN" value="1"/>
<define name="GYRO_Q_SIGN" value="1"/>
<define name="GYRO_R_SIGN" value="1"/>
<define name="ACCEL_X_NEUTRAL" value="-14"/>
<define name="ACCEL_Y_NEUTRAL" value="0"/>
<define name="ACCEL_Z_NEUTRAL" value="0"/>
<!-- SENS = 256 LSB/g @ 2.5V [X&Y: 265 LSB/g @ 3.3V] / 9.81 ms2/g = 26.095 LSB/ms2 / 10bit FRAC: 1024 / 26.095 for z and 1024 / 27.01 for X&Y -->
<define name="ACCEL_X_SENS" value="37.9" integer="16"/>
<define name="ACCEL_Y_SENS" value="37.9" integer="16"/>
<define name="ACCEL_Z_SENS" value="39.24" integer="16"/>
<define name="ACCEL_X_SIGN" value="1"/>
<define name="ACCEL_Y_SIGN" value="1"/>
<define name="ACCEL_Z_SIGN" value="1"/>
<define name="MAG_X_NEUTRAL" value="0"/>
<define name="MAG_Y_NEUTRAL" value="0"/>
<define name="MAG_Z_NEUTRAL" value="0"/>
<define name="MAG_X_SENS" value="1" integer="16"/>
<define name="MAG_Y_SENS" value="1" integer="16"/>
<define name="MAG_Z_SENS" value="1" integer="16"/>
<define name="MAG_X_SIGN" value="1"/>
<define name="MAG_Y_SIGN" value="1"/>
<define name="MAG_Z_SIGN" value="1"/>
<define name="BODY_TO_IMU_PHI" value="0"/>
<define name="BODY_TO_IMU_THETA" value="0"/>
<define name="BODY_TO_IMU_PSI" value="0"/>
</section>
<section name="INS" prefix="INS_">
<define name="ROLL_NEUTRAL_DEFAULT" value="0" unit="deg"/>
<define name="PITCH_NEUTRAL_DEFAULT" value="0" unit="deg"/>
</section>
<section name="AUTO1" prefix="AUTO1_">
<define name="MAX_ROLL" value="0.7"/>
<define name="MAX_PITCH" value="0.7"/>
</section>
<section name="BAT">
<define name="MilliAmpereOfAdc(adc)" value="((adc) - 505) * 124.0f"/>
<define name="LOW_BAT_LEVEL" value="10.5" unit="V"/>
<define name="CRITIC_BAT_LEVEL" value="10" unit="V"/>
<define name="CATASTROPHIC_BAT_LEVEL" value="9.1" unit="V"/>
</section>
<section name="MISC">
<define name="NOMINAL_AIRSPEED" value="13." unit="m/s"/>
<define name="CARROT" value="5." unit="s"/>
<define name="CONTROL_RATE" value="60" unit="Hz"/>
<define name="XBEE_INIT" value=""ATPL2\rATRN5\rATTT80\r""/>
<!-- <define name="NO_XBEE_API_INIT" value="TRUE"/> -->
<define name="ALT_KALMAN_ENABLED" value="TRUE"/>
<define name="DEFAULT_CIRCLE_RADIUS" value="80."/>
<define name="GLIDE_AIRSPEED" value="10"/>
<define name="GLIDE_VSPEED" value="3."/>
<define name="GLIDE_PITCH" value="45" unit="deg"/>
</section>
<section name="VERTICAL CONTROL" prefix="V_CTL_">
<define name="POWER_CTL_BAT_NOMINAL" value="11.1" unit="volt"/>
<!-- outer loop proportional gain -->
<define name="ALTITUDE_PGAIN" value="-0.03"/>
<!-- outer loop saturation -->
<define name="ALTITUDE_MAX_CLIMB" value="2."/>
<!-- auto throttle inner loop -->
<define name="AUTO_THROTTLE_NOMINAL_CRUISE_THROTTLE" value="0.32"/>
<define name="AUTO_THROTTLE_MIN_CRUISE_THROTTLE" value="0.25"/>
<define name="AUTO_THROTTLE_MAX_CRUISE_THROTTLE" value="0.65"/>
<define name="AUTO_THROTTLE_LOITER_TRIM" value="1500"/>
<define name="AUTO_THROTTLE_DASH_TRIM" value="-4000"/>
<define name="AUTO_THROTTLE_CLIMB_THROTTLE_INCREMENT" value="0.15" unit="%/(m/s)"/>
<define name="AUTO_THROTTLE_PGAIN" value="-0.01"/>
<define name="AUTO_THROTTLE_IGAIN" value="0.1"/>
<define name="AUTO_THROTTLE_PITCH_OF_VZ_PGAIN" value="0.05"/>
<define name="THROTTLE_SLEW_LIMITER" value="2" unit="s"/>
</section>
<section name="HORIZONTAL CONTROL" prefix="H_CTL_">
<define name="COURSE_PGAIN" value="-1.20000004768"/>
<define name="COURSE_DGAIN" value="0.3"/>
<define name="COURSE_PRE_BANK_CORRECTION" value="0.2"/>
<define name="ROLL_MAX_SETPOINT" value="0.75" unit="radians"/>
<define name="PITCH_MAX_SETPOINT" value="0.5" unit="radians"/>
<define name="PITCH_MIN_SETPOINT" value="-0.5" unit="radians"/>
<define name="PITCH_PGAIN" value="-12000."/>
<define name="PITCH_DGAIN" value="1.5"/>
<define name="ELEVATOR_OF_ROLL" value="1000."/>
<define name="ROLL_SLEW" value="1."/>
<define name="ROLL_ATTITUDE_GAIN" value="-7500"/>
<define name="ROLL_RATE_GAIN" value="0."/>
</section>
<section name="AGGRESSIVE" prefix="AGR_">
<define name="BLEND_START" value="20"/><!-- Altitude Error to Initiate Aggressive Climb CANNOT BE ZERO!!-->
<define name="BLEND_END" value="10"/><!-- Altitude Error to Blend Aggressive to Regular Climb Modes CANNOT BE ZERO!!-->
<define name="CLIMB_THROTTLE" value="1.00"/><!-- Gaz for Aggressive Climb -->
<define name="CLIMB_PITCH" value="0.3"/><!-- Pitch for Aggressive Climb -->
<define name="DESCENT_THROTTLE" value="0.1"/><!-- Gaz for Aggressive Decent -->
<define name="DESCENT_PITCH" value="-0.25"/><!-- Pitch for Aggressive Decent -->
<define name="CLIMB_NAV_RATIO" value="0.8"/><!-- Percent Navigation for Altitude Error Equal to Start Altitude -->
<define name="DESCENT_NAV_RATIO" value="1.0"/>
</section>
<section name="FAILSAFE" prefix="FAILSAFE_">
<define name="DEFAULT_THROTTLE" value="0.35" unit="%"/>
<define name="DEFAULT_ROLL" value="0.17" unit="rad"/>
<define name="DEFAULT_PITCH" value="0.08" unit="rad"/>
<define name="HOME_RADIUS" value="DEFAULT_CIRCLE_RADIUS" unit="m"/>
<define name="KILL_MODE_DISTANCE" value="(MAX_DIST_FROM_HOME*1.5)"/>
<define name="DELAY_WITHOUT_GPS" value="3" unit="s"/>
</section>
<section name="DIGITAL_CAMERA" prefix="DC_">
<define name="AUTOSHOOT_QUARTERSEC_PERIOD" value="6" unit="quarter_second"/>
<define name="AUTOSHOOT_METER_GRID" value="50" unit="meter"/>
</section>
<modules>
<!--
<load name="light.xml">
<define name="LIGHT_LED_STROBE" value="3"/>
<define name="LIGHT_LED_NAV" value="2"/>
<define name="STROBE_LIGHT_MODE_DEFAULT" value="6"/>
<define name="NAV_LIGHT_MODE_DEFAULT" value="4"/>
</load>
-->
<!-- <load name="digital_cam_i2c.xml"/> -->
<!-- <load name="ins_ppzuavimu.xml" /> -->
<!--
<load name="digital_cam.xml" >
<define name="DC_SHUTTER_LED" value="3"/>
</load>
-->
</modules>
<firmware name="fixedwing">
<target name="ap" board="lisa_l_1.1"> <!-- board="tiny_2.11"> -->
<define name="STRONG_WIND"/>
<define name="WIND_INFO"/>
<define name="WIND_INFO_RET"/>
<configure name="PERIODIC_FREQUENCY" value="120"/>
<configure name="AHRS_PROPAGATE_FREQUENCY" value="100"/>
<configure name="AHRS_CORRECT_FREQUENCY" value="100"/>
<define name="AHRS_TRIGGERED_ATTITUDE_LOOP" />
<configure name="AHRS_ALIGNER_LED" value="3"/>
<configure name="CPU_LED" value="3"/>
</target>
<target name="sim" board="pc"/>
<define name="AGR_CLIMB"/>
<define name="LOITER_TRIM"/>
<define name="ALT_KALMAN"/>
<!-- Sensors -->
<!--
<subsystem name="ahrs" type="int_cmpl_quat">
<define name="AHRS_GRAVITY_UPDATE_COORDINATED_TURN" />
</subsystem>
<subsystem name="imu" type="aspirin_i2c"/>
-->
<subsystem name="imu" type="aspirin"/>
<subsystem name="ahrs" type="dcm">
<!-- <define name="USE_MAGNETOMETER" /> -->
</subsystem>
<subsystem name="radio_control" type="ppm"/>
<!-- Communication -->
<subsystem name="telemetry" type="transparent">
<configure name="MODEM_BAUD" value="B57600"/>
<configure name="MODEM_PORT" value="UART2"/>
</subsystem>
<!-- Actuators -->
<subsystem name="control"/>
<!-- Sensors -->
<subsystem name="navigation"/>
<subsystem name="gps" type="ublox_utm">
<configure name="GPS_PORT" value="UART3"/>
</subsystem>
</firmware>
</airframe>
2011/10/28 Jochen Rieger
<address@hidden>
Ok now the telemetry works. I dont now what the reason is.
But the Failure error is still show in the window. Perhaps in additional the Failure ("Pprz.values_of_payload, too many bytes: 00 03 58 2a 00 00 00 00 00 00 00 00 00 00 00 00")
Ok, the battery status is right in GSC but where can i see the imu values?
-Jochen