[Top][All Lists]
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: AW: AW: [Paparazzi-devel] GCS problems
From: |
Maik Höpfel |
Subject: |
Re: AW: AW: [Paparazzi-devel] GCS problems |
Date: |
Wed, 7 Jul 2010 12:07:59 +0200 |
Hey Roman,
did you read Chris' response? Make sure your airframe file is set to
serial communication, not the Xbee protocol.
Also, power up your plane/setup and use whatever serial terminal
you're using to see if you have any messages coming in on the ground
station side of things. It will be gibberish, but you should get a
constant stream of data.
Regards,
Maik
2010/7/7 Gareth Roberts <address@hidden>:
> Do you definitely have bidirectional communication then? Have you checked
> all the hardware connections are 100% between the paparazzi and the xbee?
> Maybe worth checking with a multimeter or something?
> --G
>
> On 6 Jul 2010, at 21:38, Roman Nikitin wrote:
>
>>
>> Gareth,
>>
>>> Which session are you launching in GCS? Flight-USB address@hidden
>> Yes, I do.
>>
>>> Are there no errors in the paparazzi centre?
>> No errors. Data link, Server and GCS are running.
>>
>>> Have you tried launching the "Messages" tool to see if there is anything
>> sporadically coming in?
>> Yes, I did. No messages are to see.
>>
>> It is strange, that the light on the modem for "data in" is not blinking at
>> all. But it do blinking when it is connected to the X-CTU. As I can see the
>> modem send the data does not receive any back.
>>
>> Ideas?
>>
>> Roman
>>
>> -----Ursprüngliche Nachricht-----
>> Von: address@hidden
>> [mailto:address@hidden Im Auftrag
>> von Gareth Roberts
>> Gesendet: Dienstag, 6. Juli 2010 20:51
>> An: address@hidden
>> Betreff: Re: AW: [Paparazzi-devel] Modem communication problems
>>
>> That's a good start.
>> Which session are you launching in GCS? Flight-USB address@hidden
>> Are there no errors in the paparazzi centre?
>> Have you tried launching the "Messages" tool to see if there is anything
>> sporadically coming in?
>>
>> --G
>> On 6 Jul 2010, at 20:30, Roman Nikitin wrote:
>>
>>> I proved the communication between the modems with help of the X-CTU
>>> software. It is definitely working by now. The "data in" led is also fine.
>>> So the problem is somewhere in GCS.
>>>
>>
>>
>> _______________________________________________
>> Paparazzi-devel mailing list
>> address@hidden
>> http://lists.nongnu.org/mailman/listinfo/paparazzi-devel
>
>
> _______________________________________________
> Paparazzi-devel mailing list
> address@hidden
> http://lists.nongnu.org/mailman/listinfo/paparazzi-devel
>
- RE: [Paparazzi-devel] New µC Tar get with FPU?, mark.griffin, 2010/07/06
- Re: [Paparazzi-devel] New µC Target with FPU?, antoine drouin, 2010/07/06
- [Paparazzi-devel] Modem communication problems, Roman Nikitin, 2010/07/06
- Re: [Paparazzi-devel] Modem communication problems, Gareth Roberts, 2010/07/06
- AW: [Paparazzi-devel] Modem communication problems, Roman Nikitin, 2010/07/06
- AW: [Paparazzi-devel] Modem communication problems, Roman Nikitin, 2010/07/06
- Re: AW: [Paparazzi-devel] Modem communication problems, Gareth Roberts, 2010/07/06
- AW: AW: [Paparazzi-devel] GCS problems, Roman Nikitin, 2010/07/06
- Re: AW: AW: [Paparazzi-devel] GCS problems, Gareth Roberts, 2010/07/06
- Re: AW: AW: [Paparazzi-devel] GCS problems,
Maik Höpfel <=
- AW: AW: AW: [Paparazzi-devel] GCS problems, Roman Nikitin, 2010/07/08