paparazzi-devel
[Top][All Lists]
Advanced

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Paparazzi-devel] RC signal lost not clean and tiny reset issue


From: Todd Sandercock
Subject: Re: [Paparazzi-devel] RC signal lost not clean and tiny reset issue
Date: Sat, 4 Apr 2009 20:55:17 -0700 (PDT)

I think an eagle tree system can be used in flight to record servo current draw and the voltage to the servo's

Todd

From: Jerry Van Baren <address@hidden>
To: address@hidden
Sent: Sunday, 5 April, 2009 12:05:57 PM
Subject: Re: [Paparazzi-devel] RC signal lost not clean and tiny reset issue

Gareth Roberts wrote:
> miles wrote:
>>
>> On Fri, Apr 3, 2009 at 17:19, Paul Cox <address@hidden <mailto:address@hidden>> wrote:
>>
>>    2) In manual mode, moving all servos to their extremes
>>    simultaneously (rudder, ailerons, elevator) I can get the Tiny to
>>    reset. I am using a charged 3S pack and the voltage reported in
>>    the GCS looks really good (12.3), but obviously there must be some
>>    dip or spike that's affecting the processor enough to reset it.
>>    What are your suggestions?
>>
>>
>> My group has run into that also.  As a temporary work-around, we power the receiver and servos from a separate battery (not connected to Tiny2.11).  Be careful to disconnect the power line between the Tiny2.11 and receiver -- if not you will *damage* the Tiny2.11, at least the voltage regulator.
>>
>> For us, the problem was even worse than reseting the Tiny2.11, it put the Tiny2.11 in a strange mode where the servos would twitch periodically and not respond to Manual RC commands.
>>
>> Does anyone know of a nice way to determine the total power drawn by all the servos actuating a full strength simultaneously?  I guess there should also be a calculation to compute a rough upper bound on this.
>>
>> Cheers,
>> -- miles
>> ------------------------------------------------------------------------
> Couldn't you put a multimeter (on dc current mode) between the tiny and the battery?  Measure the baseline current draw, then actuate one servo to full and so on, measuring each one.  I'd be interested in the result as well, we only use two servos (aeriolons) + motor controller so haven't hit that particular problem. The other thing you could do is feed the PPM signal back to the radio, as someone was discussing on here a few weeks ago, and have that run the servos.
>
> Hope this helps
> --G

Since servos are motor-driven, they will draw a *lot* more current when loaded and slewing than when they are standing still.  It is going to be hard to measure peak current - that will likely be when the servo accelerates from stopped to full speed (max slew rate) while fully loaded.  For a give servo part number, I would expect the max current draw to be reasonably similar.  It will vary widely between different types and models of servos (different motor sizes and efficiencies).

Problems:
1) A multimeter isn't going to measure this since it is going to be a short transient current draw.  A digital (storage) scope set up for current measurement (voltage drop across a small resistor) theoretically will work.
2) It is going to be hard to implement "fully loaded" or even simulating a representative load.  Perhaps set up the servo on a bench with a spring providing the load?

If you figure out who to ask and get lucky, perhaps your servo supplier can tell you what the max current draw is for the servo you are using.

Good luck,
gvb


_______________________________________________
Paparazzi-devel mailing list
address@hidden
http://lists.nongnu.org/mailman/listinfo/paparazzi-devel


Enjoy a safer web experience. Upgrade to the new Internet Explorer 8 optimised for Yahoo!7. Get it now..
reply via email to

[Prev in Thread] Current Thread [Next in Thread]