[paparazzi-commits] [6367] Consolidated ppz4 controller directory with hw.

[Piotr Esden-Tempski]

Revision: 6367
          http://svn.sv.gnu.org/viewvc/?view=rev&root=paparazzi&revision=6367
Author:   esden
Date:     2010-11-07 00:19:29 +0000 (Sun, 07 Nov 2010)
Log Message:
-----------
Consolidated ppz4 controller directory with hw.

Added Paths:
-----------
    paparazzi4/trunk/hw/classix/
    paparazzi4/trunk/hw/classix/TODO
    paparazzi4/trunk/hw/classix/v0.99/
    paparazzi4/trunk/hw/classix/v0.99/classix.brd
    paparazzi4/trunk/hw/classix/v0.99/classix.sch
    paparazzi4/trunk/hw/tiny/
    paparazzi4/trunk/hw/tiny/v0.99/
    paparazzi4/trunk/hw/tiny/v0.99/TODO
    paparazzi4/trunk/hw/tiny/v0.99/tiny.brd
    paparazzi4/trunk/hw/tiny/v0.99/tiny.sch
    paparazzi4/trunk/hw/tiny/v1.1/
    paparazzi4/trunk/hw/tiny/v1.1/TODO
    paparazzi4/trunk/hw/tiny/v1.1/tiny.brd
    paparazzi4/trunk/hw/tiny/v1.1/tiny.sch

Removed Paths:
-------------
    paparazzi4/trunk/paparazzi3-hw/controller/

Copied: paparazzi4/trunk/hw/classix/TODO (from rev 6365, 
paparazzi4/trunk/paparazzi3-hw/controller/TODO_classix)
===================================================================
--- paparazzi4/trunk/hw/classix/TODO                            (rev 0)
+++ paparazzi4/trunk/hw/classix/TODO    2010-11-07 00:19:29 UTC (rev 6367)
@@ -0,0 +1,12 @@
+06/01/01 : V0.9
+pullups P0.14
+pullup gumstix I2C on wrong side
+
+06/03/25 :
+fixed pullup P0.14 and gum i2c pullup - Poine
+
+06/04/25:
+change label for FOO connector ( rc receiver )
+add a resitor on the input capture line
+
+add a diode in the USB vbus

Copied: paparazzi4/trunk/hw/classix/v0.99/classix.brd (from rev 6365, 
paparazzi4/trunk/paparazzi3-hw/controller/classix.brd)
===================================================================
(Binary files differ)

Copied: paparazzi4/trunk/hw/classix/v0.99/classix.sch (from rev 6365, 
paparazzi4/trunk/paparazzi3-hw/controller/classix.sch)
===================================================================
(Binary files differ)

Copied: paparazzi4/trunk/hw/tiny/v0.99/TODO (from rev 6365, 
paparazzi4/trunk/paparazzi3-hw/controller/TODO_tiny)
===================================================================
--- paparazzi4/trunk/hw/tiny/v0.99/TODO                         (rev 0)
+++ paparazzi4/trunk/hw/tiny/v0.99/TODO 2010-11-07 00:19:29 UTC (rev 6367)
@@ -0,0 +1,36 @@
+#### tiny_proto : first batch, christmas 2005 
+
+
++add supply measurement
++add crystal direction mark in library
++remove button pullup from under the button
++add a pullup for P0.14
++expose P0.23 for USB bootloader
++expose one IT on SPI connector to enable slave's notification (DRDY)
+-improve serigraphy
++ make GPS middle pin bStop big enough
+? maybe add possibility to solder lithium battery instead of gold cap, without 
adding a drill (with thermal) in the ground patch area
++ add tStop under the (rectangle) gps patch (not sure if it will help, but 
seen elsewhere)
+- adjust LEA-xx dimension (part is taller than in .lbr)
+- adjust LEA-xx pad width (pads are thinner than in .lbr)
++ (try Digikey patch antenna/adjust board to it)
++ use 13mm Sangshin antenna
++ make the board compatible with LEA-LA by adding GPS mode solder bridges : 
only for separate GPS boards
++ wire GPS reset : NO
++ make through-holes under LEA have tStop even on holes to prevent (rare) 
short circuit to LEA : use PCB varnish instead
++rewire 4015 on a single output compare
+- add resitor bridge for USB_VBUS
++(GRZ) on serigraphy, replace
++ "S2" with "S0" on servo connector
++ "S3" with "S4" on servo connector
++ "S4" with "S5" on servo connector
+- add a diode in the USB VBUS detection
+###### tiny 0.99
+
+###### tiny13_1_1 and tiny20_1_1
+
+-remove audio hardware
+-add command/data and cts to serial1 connector ( for radiotronix )
+-swap uarts and expose CTS for modem that do hw flow control ??
+-add a "switched" power connector
+

Copied: paparazzi4/trunk/hw/tiny/v0.99/tiny.brd (from rev 6365, 
paparazzi4/trunk/paparazzi3-hw/controller/tiny_0_99.brd)
===================================================================
(Binary files differ)

Copied: paparazzi4/trunk/hw/tiny/v0.99/tiny.sch (from rev 6365, 
paparazzi4/trunk/paparazzi3-hw/controller/tiny_0_99.sch)
===================================================================
(Binary files differ)

Copied: paparazzi4/trunk/hw/tiny/v1.1/TODO (from rev 6365, 
paparazzi4/trunk/paparazzi3-hw/controller/TODO_tiny13)
===================================================================
--- paparazzi4/trunk/hw/tiny/v1.1/TODO                          (rev 0)
+++ paparazzi4/trunk/hw/tiny/v1.1/TODO  2010-11-07 00:19:29 UTC (rev 6367)
@@ -0,0 +1,2 @@
+- missing ppm_out and ppm_reset on rc rx connector
+- add decoupling capacitors to servo output ?

Copied: paparazzi4/trunk/hw/tiny/v1.1/tiny.brd (from rev 6365, 
paparazzi4/trunk/paparazzi3-hw/controller/tiny13_1_1.brd)
===================================================================
(Binary files differ)

Copied: paparazzi4/trunk/hw/tiny/v1.1/tiny.sch (from rev 6365, 
paparazzi4/trunk/paparazzi3-hw/controller/tiny13_1_1.sch)
===================================================================
(Binary files differ)