[paparazzi-builds] [paparazzi] Build failed : master #1686

[Semaphore]

Build 1686 Failed For project paparazzi on branch master

View on Semaphore

Last commit for this build

	OpenUAS	16 May 08:54
124fa32 — Update opticflow_calculator.c

Build Results

01:04:18

Thread #1

ls -lah $SEMAPHORE_CACHE_DIR

00:00

df -h

00:00

docker pull flixr/pprz-dev

01:29

df -h

00:00

sudo rm -rf /home/runner/{.phpbrew,.phpunit,.kerl,.kiex,.lein,.nvm,.npm,.rbenv}

00:23

df -h

00:00

git --version

00:00

git status --ignored

00:00

git submodule deinit --force .

00:00

rm -rf .git/modules

00:00

git submodule update --init --force --recursive

01:37

if [ "$SEMAPHORE_TRIGGER_SOURCE" = "scheduler" ]; then docker/run.sh -it flixr/pprz-dev make test_all_confs ; else docker/run.sh -it flixr/pprz-dev make test ; fi

01:00:01

( Showing only the last 30 out of 82 lines. For a complete log visit the build page )

         #define ActuatorPwmSet(_i, _v) { actuators_pwm_values[_i] = _v; }
                                  ~~~~~~~~~~~~~~~~~~~~^~~~
/home/pprz/paparazzi/var/aircrafts/Racer_PEX_Octo/ap/generated/airframe.h:160:3: note: in expansion of macro 'ActuatorPwmSet'
   ActuatorPwmSet(SERVO_BL_7, actuators[SERVO_BL_7_IDX]); \
   ^~~~~~~~~~~~~~
/home/pprz/paparazzi/var/aircrafts/Racer_PEX_Octo/ap/generated/airframe.h:255:3: note: in expansion of macro 'Set_BL_7_Servo'
   Set_BL_7_Servo(servo_value); \
   ^~~~~~~~~~~~~~
firmwares/rotorcraft/main_ap.c:264:3: note: in expansion of macro 'SetActuatorsFromCommands'
   SetActuatorsFromCommands(commands, autopilot_get_mode());
   ^~~~~~~~~~~~~~~~~~~~~~~~

/home/pprz/paparazzi/sw/airborne/arch/stm32/subsystems/actuators/actuators_pwm_arch.h:43:54: warning: array subscript is above array bounds [-Warray-bounds]
 #define ActuatorPwmSet(_i, _v) { actuators_pwm_values[_i] = _v; }
                                  ~~~~~~~~~~~~~~~~~~~~^~~~
/home/pprz/paparazzi/var/aircrafts/Racer_PEX_Octo/ap/generated/airframe.h:166:3: note: in expansion of macro 'ActuatorPwmSet'
   ActuatorPwmSet(SERVO_FL_8, actuators[SERVO_FL_8_IDX]); \
   ^~~~~~~~~~~~~~
/home/pprz/paparazzi/var/aircrafts/Racer_PEX_Octo/ap/generated/airframe.h:261:3: note: in expansion of macro 'Set_FL_8_Servo'
   Set_FL_8_Servo(servo_value); \
   ^~~~~~~~~~~~~~
firmwares/rotorcraft/main_ap.c:264:3: note: in expansion of macro 'SetActuatorsFromCommands'
   SetActuatorsFromCommands(commands, autopilot_get_mode());
   ^~~~~~~~~~~~~~~~~~~~~~~~


# compiling AIRCRAFT: [Racer_PEX_Octo] TARGET: [nps]

tests/aircrafts/01_compile_all_aircrafts.t .. 5/61 # compiling AIRCRAFT: [Racer_PEX_Quad] TARGET: [ap]

tests/aircrafts/01_compile_all_aircrafts.t .. 6/61 # compiling AIRCRAFT: [Racer_PEX_Quad] TARGET: [nps]
execution expired
      

df -h

00:00

Manage your email notification settings.

Is this email not displaying correctly? Report the issue.

Sent by Semaphore