[monit] thermal status

[francis]

Hello Martin,

I have monit running in my servers. Onne of the servers went restarted but i suspect overheating.
Is there a way that i can monitor thermal status of a system?
With regards 
Francis Kamau

 

> -----Original Message-----
> From: Martin Pala [mailto:address@hidden
> Sent: Tuesday, April 29, 2008 03:34 PM
> To: 'This is the general mailing list for monit'
> Subject: Re: [monit] Quad Core Monitoring
>
> Monit is reporting the CPU usage as total (corresponding to first
> example of top).
>
> If the application will get 100% of one core on 4-core system, it's CPU
> usage should be reported by monit is 25% (since 4 * 25% = 100%).
>
> You can thus use rule like this:
>
>    if cpu usage > 25% then restart
>
> Martin
>
>
>
> address@hidden wrote:
> > We have an issue were mysqld hogs up 100% of one of our cpu cores from
> > time to time.  How can I configure monit to restart mysqld when this
> > happens.
> >
> > For an example of what I am talking about, top normally shows only one
> > cpu but if you press '1' it will show all the cpus.
> > (normal top)
> > top - 18:13:11 up 10 days, 21:59,  1 user,  load average: 1.56, 1.81, 2.08
> > Tasks: 186 total,   5 running, 181 sleeping,   0 stopped,   0 zombie
> > Cpu(s): 31.6% us,  7.6% sy,  0.0% ni, 60.8% id,  0.0% wa,  0.0% hi,  0.0% si
> >
> > (top after pressing '1')
> > top - 18:13:54 up 10 days, 22:00,  1 user,  load average: 1.73, 1.81, 2.07
> > Tasks: 185 total,   3 running, 182 sleeping,   0 stopped,   0 zombie
> > Cpu0  : 29.4% us,  5.9% sy,  0.0% ni, 63.9% id,  0.7% wa,  0.0% hi,  0.0% si
> > Cpu1  : 27.9% us,  5.6% sy,  0.0% ni, 65.5% id,  1.0% wa,  0.0% hi,  0.0% si
> > Cpu2  : 23.1% us,  5.7% sy,  0.0% ni, 70.6% id,  0.7% wa,  0.0% hi,  0.0% si
> > Cpu3  : 25.3% us,  6.2% sy,  0.0% ni, 67.5% id,  1.0% wa,  0.0% hi,  0.0% si
> >
> > (sample when mysqld is hogging cpu time)
> > top - 18:13:54 up 10 days, 22:00,  1 user,  load average: 1.73, 1.81, 2.07
> > Tasks: 185 total,   3 running, 182 sleeping,   0 stopped,   0 zombie
> > Cpu0  : 100 % us,  5.9% sy,  0.0% ni, 63.9% id,  0.7% wa,  0.0% hi,  0.0% si
> > Cpu1  : 7.9% us,  5.6% sy,  0.0% ni, 65.5% id,  1.0% wa,  0.0% hi,  0.0% si
> > Cpu2  : 3.1% us,  5.7% sy,  0.0% ni, 70.6% id,  0.7% wa,  0.0% hi,  0.0% si
> > Cpu3  : 5.3% us,  6.2% sy,  0.0% ni, 67.5% id,  1.0% wa,  0.0% hi,  0.0% si
> >
> > So, how do I get monit to restart mysqld when just one cpu is pegged at
> > 100%?  It's not always Cpu0, it could be any of them.
> >
> > Thanks,
> >
> >
> > ------------------------------------------------------------------------
> >
> > --
> > To unsubscribe:
> > http://lists.nongnu.org/mailman/listinfo/monit-general
>
>
> --
> To unsubscribe:
> http://lists.nongnu.org/mailman/listinfo/monit-general