[Ltib] libusb

[Chris Westervelt]

Stuart,

 

I have sent a shout out to the group to try and get some feedback on why libusb will not build for me.  No one has responded to either of my request so I was wondering if you could help me.  Below is the output I’m seeing when it builds.

 

./libtool: line 454: CDPATH: command not found

./libtool: line 454: CDPATH: command not found

./libtool: line 454: CDPATH: command not found

./libtool: line 454: CDPATH: command not found

./libtool: line 1132: func_opt_split: command not found

libtool: Version mismatch error.  This is libtool 2.2.6b

Debian-2.2.6b-2ubuntu1, but the

libtool: definition of this LT_INIT comes from an older release.

libtool: You should recreate aclocal.m4 with macros from libtool 2.2.6b

Debian-2.2.6b-2ubuntu1

libtool: and run autoconf again.

./libtool: line 1132: func_opt_split: command not found

./libtool: line 1132: func_opt_split: command not found

make[2]: *** [error.lo] Error 1

make[2]: *** Waiting for unfinished jobs....

libtool: Version mismatch error.  This is libtool 2.2.6b

Debian-2.2.6b-2ubuntu1, but the

libtool: definition of this LT_INIT comes from an older release.

libtool: You should recreate aclocal.m4 with macros from libtool 2.2.6b

Debian-2.2.6b-2ubuntu1

libtool: and run autoconf again.

libtool: Version mismatch error.  This is libtool 2.2.6b

Debian-2.2.6b-2ubuntu1, but the

libtool: definition of this LT_INIT comes from an older release.

libtool: You should recreate aclocal.m4 with macros from libtool 2.2.6b

Debian-2.2.6b-2ubuntu1

libtool: and run autoconf again.

make[2]: *** [linux.lo] Error 1

make[2]: *** [descriptors.lo] Error 1

./libtool: line 1132: func_opt_split: command not found

libtool: Version mismatch error.  This is libtool 2.2.6b

Debian-2.2.6b-2ubuntu1, but the

libtool: definition of this LT_INIT comes from an older release.

libtool: You should recreate aclocal.m4 with macros from libtool 2.2.6b

Debian-2.2.6b-2ubuntu1

libtool: and run autoconf again.

make[2]: *** [usb.lo] Error 1

make[2]: Leaving directory

`/home/chris/Desktop/ltib-igii-34-dev/ltib-igii/ltib/rpm/BUILD/libusb-0.1.8'

make[1]: *** [all-recursive] Error 1

make[1]: Leaving directory

`/home/chris/Desktop/ltib-igii-34-dev/ltib-igii/ltib/rpm/BUILD/libusb-0.1.8'

make: *** [all] Error 2

error: Bad exit status from

/home/chris/Desktop/ltib-igii-34-dev/ltib-igii/ltib/tmp/rpm-tmp.30599 (%build)

 

 

RPM build errors:

    Bad exit status from

/home/chris/Desktop/ltib-igii-34-dev/ltib-igii/ltib/tmp/rpm-tmp.30599 (%build)

Build time for libusb: 10 seconds

 

Failed building libusb

 

 

Chris Westervelt

Senior Product Development Engineer

Advantor Systems.
12612 Challenger Pkwy
Suite 300
Orlando, FL
32826

http://www.infrasafe.com
Office:   (407) 926-6983

Mobile: (407) 595-7023       
Fax:    (407) 857-1635
Notice of Confidentiality:
This e-mail communication and the attachments hereto, if any, are intended solely for the information and use of the addressee(s) identified above and may contain information which is legally privileged and/or otherwise confidential. If a recipient of this e-mail communication is not an addressee (or an authorized representative of an addressee), such recipient is hereby advised that any review, disclosure, reproduction, re-transmission or other dissemination or use of this e-mail communication (or any information contained herein) is strictly prohibited. If you are not an addressee and have received this e-mail communication in error, please advise the sender of that circumstance either by reply e-mail or by telephone at (800) 238-2686, immediately delete this e-mail communication from any computer and destroy all physical copies of same.