Hi,
I'm not sure if this is really the right place to ask, but since the
issue I have is related to problems encountered when updating the
version of Ltib I'm using - I thought it would be a good place to start.
I'm using the ltib from freescale for the MPC8315E Power quicc
processor. I was previously using the release that came with the dev
board dated 20080630, which used u-boot 1.20 to NFS boot my board.
I have switched to the latest ltib release dated 20091019 but I can't
get my board to boot correcly with the new linux kernel & u-boot images
that I've built.
I've programmed the latest flavour of u-boot into my board, but it fails
when trying to boot into linux. Here's the boot-up output :
U-Boot 2009.03-rc2 (Jan 07 2010 - 15:47:10) MPC83XX
Reset Status:
CPU: e300c3, MPC8315E, Rev: 1.1 at 400 MHz, CSB: 133.333 MHz
Board: Freescale MPC8315ERDB Rev 1.0
I2C: ready
DRAM: 128 MB
FLASH: 8 MB
NAND: 32 MiB
PCIE0: No link
PCIE1: No link
In: serial
Out: serial
Err: serial
Net: eTSEC0, eTSEC1
Hit any key to stop autoboot: 0
Speed: 100, full duplex
Using eTSEC0 device
TFTP from server 192.168.20.3; our IP address is 192.168.20.10
Filename 'uImage'.
Load address: 0x500000
Loading: #################################################################
#################################################################
###########
done
Bytes transferred = 2069379 (1f9383 hex)
Speed: 100, full duplex
Using eTSEC0 device
TFTP from server 192.168.20.3; our IP address is 192.168.20.10
Filename 'mpc8315erdb-default.dtb'.
Load address: 0x400000
Loading: #
done
Bytes transferred = 9953 (26e1 hex)
## Booting kernel from Legacy Image at 00500000 ...
Image Name: Linux-2.6.29.6-rt23
Created: 2010-01-07 15:31:48 UTC
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 2069315 Bytes = 2 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 00400000
Booting using the fdt blob at 0x400000
Uncompressing Kernel Image ... OK
ERROR: image is not a fdt - must RESET the board to recover.
Resetting the board.
At which point, the unit reboots & starts all over again.
I've checked that the version of mpc8315erdb-default.dtb is the one
built by the latest ltib.
Not sure where to go from here -- anyone got any ideas ?
Thanks in advance.
Rob Belcham
Principal DSP Engineer
*Midas and Klark Teknik*
/Please note my email will be changing shortly to
/address@hidden <mailto:address@hidden>./ Please
update your records accordingly/
Switch Board: +44 1562 741515
_www.midasconsoles.com_ <http://www.midasconsoles.com/> │
_www.klarkteknik.com_ <http://www.klarkteknik.com/> │
_www.ktsquareone.com_ <http://www.ktsquareone.com/>
*Bosch Communications Systems
*Telex Communications (UK) Limited, Limited Company, Number 2414018,
Incorporated in England.
Registered Office:
Klark Industrial Park, Walter Nash Road, Kidderminster. Worcestershire.
DY11 7HJ. UK.
*Warning!* The information contained in this e-mail is confidential and
is intended for the use only of the addressee.
Any unauthorised dissemination or copying of this e-mail and any use or
disclosure of information contained in it is strictly prohibited and may
be illegal.
Please note that we cannot accept any responsibility for any transmitted
viruses. It is therefore your responsibility to virus scan attachments.
------------------------------------------------------------------------
_______________________________________________
LTIB home page: http://ltib.org
Ltib mailing list
address@hidden
http://lists.nongnu.org/mailman/listinfo/ltib