[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
RE: Control toolbox having ss2tf, tf2ss, ss2sys, tf2sys, lsim, etc missi
From: |
Shrikrishna.Joshi |
Subject: |
RE: Control toolbox having ss2tf, tf2ss, ss2sys, tf2sys, lsim, etc missing |
Date: |
Tue, 20 Jul 2010 13:18:53 +0530 |
Thank you.
This way it works.
Regards,
Shrikrishna C Joshi
Engineering Research CentreĀ | Tata Motors Ltd. Premises
Pimpri | Pune 411018
p: +91 20 6613 5322
email:address@hidden
website: www.tatatechnologies.com
-----Original Message-----
From: Tatsuro MATSUOKA [mailto:address@hidden
Sent: 20 July 2010 12:33
To: address@hidden; Joshi Shrikrishna [Project Manager - PDV]; address@hidden
Cc: address@hidden
Subject: RE: Control toolbox having ss2tf, tf2ss, ss2sys, tf2sys, lsim, etc
missing
Hello
:From octave ver 3, the axis command (also other plot related commands like
xlabel) should be executed
after plot command.
(This way is compatible to that of the current MATLAB. )
plot command
plot related command like axis, xlabel, etcs.
drawnow(); (if required for example plot command in loop)
Regards
Tatsuro
--- Tatsuro MATSUOKA wrote:
> Hello
>
> Please add
>
> drawnow();
>
> just after plot command.
>
> Regards
>
> Tatsuro
> --- Shrikrishna.Joshi wrote:
>
> > my query:
> >
> > The command of "axis" is ignored if we plot in the for loop.
> >
> > With earlier version on IRIX operating system the command was honoured.
> >
> >
> >
> >
> >
> > your comment:
> >
> > You haven't really supplied enough information. As far as I can see the
> >
> > axis command works as expected.
> >
> >
> >
> >
> >
> > I am simulating crank-piston mechanism with torques and forces applied.
> >
> > I wanted to visualize / animate the mechanism after solving it.
> >
> > For this reason I gave the following command:
> >
> >
> >
> > axis([-1 5 -1 5],"square");
> >
> > for k=1:10:length(Xa)
> >
> > system(" ",sleep(0.05));
> >
> > plot([xo Xa(k) Xb(k)],[yo Ya(k) Yb(k)]);
> >
> > end
> >
> >
> >
> > another variant
> >
> >
> >
> > for k=1:10:length(Xa)
> >
> > system(" ",sleep(0.05));
> >
> > axis([-1 5 -1 5],"square");
> >
> > plot([xo Xa(k) Xb(k)],[yo Ya(k) Yb(k)]);
> >
> > end
> >
> >
> >
> > The plots however are plotted with auto limits and the axis command is
> > ignored.
> >
> > Due to which the plots look quite distorted.
> >
> > Kindly suggest workaround.
> >
> >
> >
> > Regards,
> >
> >
> >
> > Shrikrishna C Joshi
> >
> > Engineering Research Centre | Tata Motors Ltd. Premises
> >
> > Pimpri | Pune 411018
> >
> > p: +91 20 6613 5322
> >
> > email: address@hidden
> >
> > website: www.tatatechnologies.com <http://www.tatatechnologies.com/>
> >
> >
> >
> >
> >
> >
> >
> > -----Original Message-----
> > From: David Bateman [mailto:address@hidden
> > Sent: 19 July 2010 20:44
> > To: Joshi Shrikrishna [Project Manager - PDV]
> > Cc: address@hidden
> > Subject: Re: Control toolbox having ss2tf, tf2ss, ss2sys, tf2sys, lsim,
> > etc missing
> >
> >
> >
> > address@hidden wrote:
> >
> > > Hello,
> >
> > >
> >
> > > 1. I have downloaded 3.2.4 (stable version) with Redhat linux. In
> >
> > > the ealier version with IRIX operating system OCST was available.
> >
> > > However with the latest download I am not able to find it.
> >
> > >
> >
> > The control toolbox was removed from Octave itself and became an
> >
> > octave-forge package. Check
> >
> >
> >
> > http://octave.sourceforge.net/control/index.html
> >
> >
> >
> > You might also what to look at the control-oo toolbox that is more
> >
> > matlab compatible. Though as this toolbox is in development you'll need
> >
> > to get it from the SVN. See
> >
> >
> >
> > http://octave.svn.sourceforge.net/viewvc/octave/trunk/octave-forge/main/
> > control/
> >
> >
> >
> > > 2. The command of "axis" is ignored if we plot in the for loop.
> >
> > > With earlier version on IRIX operating system the command was
> > honoured.
> >
> > >
> >
> > >
> >
> > You haven't really supplied enough information. As far as I can see the
> >
> > axis command works as expected.
> >
> >
> >
> >
> >
> > D.
> >
> >
> >
> >
>
**************************************************************************************************************************************************
> > Email Disclaimer:
> >
> > Information contained and transmitted by this e-mail (including any
> > attachments) is
> > confidential, proprietary and legally privileged data of Tata Technologies
> > that is intended
> for
> > use only by the addressee. If you are not the intended recipient, you are
> > notified that any
> > review, use, dissemination, distribution, copying or printing of this
> > e-mail is strictly
> > prohibited. You are requested to delete this e-mail or any copies
> > immediately and notify the
> > sender by reply email. Internet communications cannot be guaranteed to be
> > timely, secure,
> error
> > or virus-free. Tata Technologies does not accept any liability for virus
> > infected email or
> > errors or omissions or consequences which may arise as a result of this
> > e-mail transmission.
> To
> > know more about Tata Technologies please visit
> > http://www.tatatechnologies.com
> >
>
************************************************************************************************************************************************
> > > _______________________________________________
> > Help-octave mailing list
> > address@hidden
> > https://www-old.cae.wisc.edu/mailman/listinfo/help-octave
> >
>
>
> --------------------------------------
> Get the new Internet Explorer 8 optimized for Yahoo! JAPAN
> http://pr.mail.yahoo.co.jp/ie8/
> _______________________________________________
> Help-octave mailing list
> address@hidden
> https://www-old.cae.wisc.edu/mailman/listinfo/help-octave
>
--------------------------------------
Get the new Internet Explorer 8 optimized for Yahoo! JAPAN
http://pr.mail.yahoo.co.jp/ie8/
**************************************************************************************************************************************************
Email Disclaimer:
Information contained and transmitted by this e-mail (including any
attachments) is confidential, proprietary and legally privileged data of Tata
Technologies that is intended for use only by the addressee. If you are not the
intended recipient, you are notified that any review, use, dissemination,
distribution, copying or printing of this e-mail is strictly prohibited. You
are requested to delete this e-mail or any copies immediately and notify the
sender by reply email. Internet communications cannot be guaranteed to be
timely, secure, error or virus-free. Tata Technologies does not accept any
liability for virus infected email or errors or omissions or consequences which
may arise as a result of this e-mail transmission. To know more about Tata
Technologies please visit http://www.tatatechnologies.com
************************************************************************************************************************************************
- Control toolbox having ss2tf, tf2ss, ss2sys, tf2sys, lsim, etc missing, Shrikrishna.Joshi, 2010/07/19
- Re: Control toolbox having ss2tf, tf2ss, ss2sys, tf2sys, lsim, etc missing, David Bateman, 2010/07/19
- RE: Control toolbox having ss2tf, tf2ss, ss2sys, tf2sys, lsim, etc missing, Shrikrishna.Joshi, 2010/07/20
- RE: Control toolbox having ss2tf, tf2ss, ss2sys, tf2sys, lsim, etc missing, Tatsuro MATSUOKA, 2010/07/20
- RE: Control toolbox having ss2tf, tf2ss, ss2sys, tf2sys, lsim, etc missing, Tatsuro MATSUOKA, 2010/07/20
- RE: Control toolbox having ss2tf, tf2ss, ss2sys, tf2sys, lsim, etc missing,
Shrikrishna.Joshi <=