[avrdude-dev] part code for ATMEGA64A not found.

[miguel tostes]

Thanks for you attention Joerg.
Bellow it follows the received error message, then following with -vvvv:

This is an attempt to read EEPROM from ATMEGA64A:
=================================================================================
AVRDUDE Iniciado\n
C:/Arquivos de programas/eePe/avrdude.exe -c usbasp -p m64 -P usb -U
eeprom:r:C:/tur-ori-eeprom.hex:i
=================================================================================
avrdude.exe: warning: cannot set sck period. please check for usbasp
firmware update.
avrdude.exe: error: programm enable: target doesn't answer. 1
avrdude.exe: initialization failed, rc=-1
Double check connections and try again, or use -F to override this check.
avrdude.exe done. Thank you.
=================================================================================
AVRDUDE done - exit code 1
=================================================================================

------------------
This is an attempt to read EEPROM from ATMEGA64A, executing now with -vvvv:
------------------

=================================================================================
AVRDUDE Iniciado\n
C:/Arquivos de programas/eePe/avrdude.exe -c usbasp -p m64 -vvvv -P
usb -U eeprom:r:C:/eeprom-ori.bin:r
=================================================================================
avrdude.exe: Version 5.10, compiled on Jan 19 2010 at 10:45:23
Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
Copyright (c) 2007-2009 Joerg Wunsch
System wide configuration file is "C:\Arquivos de programas\eePe\avrdude.conf"
Using Port : usb
Using Programmer : usbasp
avrdude.exe: seen device from vendor ->www.fischl.de<-
avrdude.exe: seen product ->USBasp<-
AVR Part : ATMEGA64
Chip Erase delay : 9000 us
PAGEL : PD7
BS2 : PA0
RESET disposition : dedicated
RETRY pulse : SCK
serial program mode : yes
parallel program mode : yes
Timeout : 200
StabDelay : 100
CmdexeDelay : 25
SyncLoops : 32
ByteDelay : 0
PollIndex : 3
PollValue : 0x53
Memory Detail :
Block Poll Page Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack
----------- ---- ----- ----- ---- ------ ------ ---- ------ -----
----- ---------
eeprom 4 20 64 0 no 2048 8 0 9000 9000 0xff 0xff
Block Poll Page Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack
----------- ---- ----- ----- ---- ------ ------ ---- ------ -----
----- ---------
flash 33 6 128 0 yes 65536 256 256 4500 4500 0xff 0xff
Block Poll Page Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack
----------- ---- ----- ----- ---- ------ ------ ---- ------ -----
----- ---------
lfuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00
Block Poll Page Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack
----------- ---- ----- ----- ---- ------ ------ ---- ------ -----
----- ---------
hfuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00
Block Poll Page Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack
----------- ---- ----- ----- ---- ------ ------ ---- ------ -----
----- ---------
efuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00
Block Poll Page Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack
----------- ---- ----- ----- ---- ------ ------ ---- ------ -----
----- ---------
lock 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00
Block Poll Page Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack
----------- ---- ----- ----- ---- ------ ------ ---- ------ -----
----- ---------
calibration 0 0 0 0 no 4 0 0 0 0 0x00 0x00
Block Poll Page Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack
----------- ---- ----- ----- ---- ------ ------ ---- ------ -----
----- ---------
signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00
Programmer Type : usbasp
Description : USBasp, http://www.fischl.de/usbasp/
avrdude.exe: auto set sck period (because given equals null)
avrdude.exe: warning: cannot set sck period. please check for usbasp
firmware update.
avrdude.exe: error: programm enable: target doesn't answer. 1
avrdude.exe: initialization failed, rc=-1
Double check connections and try again, or use -F to override
this check.
avrdude.exe done. Thank you.
=================================================================================
AVRDUDE done - exit code 1
=================================================================================

--------------
This is an attempt to read FLASH from ATMEGA64A, with -vvvv:
--------------

=================================================================================
AVRDUDE Iniciado\n
C:/Arquivos de programas/eePe/avrdude.exe -c usbasp -p m64 -vvvv -P
usb -U flash:r:C:/flash-ori.bin:r
=================================================================================
avrdude.exe: Version 5.10, compiled on Jan 19 2010 at 10:45:23
Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
Copyright (c) 2007-2009 Joerg Wunsch
System wide configuration file is "C:\Arquivos de programas\eePe\avrdude.conf"
Using Port : usb
Using Programmer : usbasp
avrdude.exe: seen device from vendor ->www.fischl.de<-
avrdude.exe: seen product ->USBasp<-
AVR Part : ATMEGA64
Chip Erase delay : 9000 us
PAGEL : PD7
BS2 : PA0
RESET disposition : dedicated
RETRY pulse : SCK
serial program mode : yes
parallel program mode : yes
Timeout : 200
StabDelay : 100
CmdexeDelay : 25
SyncLoops : 32
ByteDelay : 0
PollIndex : 3
PollValue : 0x53
Memory Detail :
Block Poll Page Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack
----------- ---- ----- ----- ---- ------ ------ ---- ------ -----
----- ---------
eeprom 4 20 64 0 no 2048 8 0 9000 9000 0xff 0xff
Block Poll Page Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack
----------- ---- ----- ----- ---- ------ ------ ---- ------ -----
----- ---------
flash 33 6 128 0 yes 65536 256 256 4500 4500 0xff 0xff
Block Poll Page Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack
----------- ---- ----- ----- ---- ------ ------ ---- ------ -----
----- ---------
lfuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00
Block Poll Page Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack
----------- ---- ----- ----- ---- ------ ------ ---- ------ -----
----- ---------
hfuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00
Block Poll Page Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack
----------- ---- ----- ----- ---- ------ ------ ---- ------ -----
----- ---------
efuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00
Block Poll Page Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack
----------- ---- ----- ----- ---- ------ ------ ---- ------ -----
----- ---------
lock 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00
Block Poll Page Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack
----------- ---- ----- ----- ---- ------ ------ ---- ------ -----
----- ---------
calibration 0 0 0 0 no 4 0 0 0 0 0x00 0x00
Block Poll Page Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack
----------- ---- ----- ----- ---- ------ ------ ---- ------ -----
----- ---------
signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00
Programmer Type : usbasp
Description : USBasp, http://www.fischl.de/usbasp/
avrdude.exe: auto set sck period (because given equals null)
avrdude.exe: warning: cannot set sck period. please check for usbasp
firmware update.
avrdude.exe: error: programm enable: target doesn't answer. 1
avrdude.exe: initialization failed, rc=-1
Double check connections and try again, or use -F to override
this check.
avrdude.exe done. Thank you.
=================================================================================
AVRDUDE done - exit code 1
=================================================================================

Any Clues ?

MigTrib

---------- Forwarded message ----------
From: miguel tostes <address@hidden>
Date: Mon, Jan 23, 2012 at 2:45 PM
Subject: Re: [avrdude-dev] part code for ATMEGA64A not found.
To: Joerg Wunsch <address@hidden>


Programmer: usbasp

Using the same parameters as for ATMEGA64, that are '-p m64'   and
'-c usbasp'.

Using eepe front-end to avrdude.

I do not have it here with me, but at night I will post more details
(error mesages etc, and will try -vvvv ).

Thanks for the moment.

migtrib

On Mon, Jan 23, 2012 at 2:36 PM, Joerg Wunsch <address@hidden> wrote:
> As miguel tostes wrote:
>
>> I am searching more info because the EEPROM reading not worked, ...
>
> Then, Atmel didn't deliver to their promise that the ATmega64A were a
> drop-in replacement.
>
> Perhaps, you're telling us a bit more about your programmer used, and
> the parameters (or command-line).
> Did you try some debugging (using -vvvv)?
>
>> Do you know anything regarding that ATMEGA64A, or has you already 
>> programed/read
>> its EEPROM or Flash ?
>
> No, I don't have an ATmega64A handy.
> --
> cheers, J"org               .-.-.   --... ...--   -.. .  DL8DTL
>
> http://www.sax.de/~joerg/                        NIC: JW11-RIPE
> Never trust an operating system you don't have sources for. ;-)