qemu-devel
[Top][All Lists]
Advanced

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

[PATCH v8 0/3] Add device STM32L4x5 EXTI


From: Inès Varhol
Subject: [PATCH v8 0/3] Add device STM32L4x5 EXTI
Date: Tue, 9 Jan 2024 17:06:01 +0100

This patch adds a new device STM32L4x5 EXTI device and is part
of a series implementing the STM32L4x5 with a few peripherals.

Hello,
I see that the previous patch v7 couldn't be applied to master,
the log is :
...
Applying: hw/arm: Connect STM32L4x5 EXTI to STM32L4x5 SoC
error: sha1 information is lacking or useless (hw/arm/stm32l4x5_soc.c).
error: could not build fake ancestor
...
I notice there was a wrong Based-on message ID in v7 and I figure
that's the issue (since the relevant commit
"hw/arm: Connect STM32L4x5 EXTI to STM32L4x5 SoC" didn't even change
from v6). If that's not the case, I apologize in advance.

Changes from v7 to v8:
- none except for "Based-on" message-id correction

Changes from v6 to v7:
- in `stm32l4x5_exti_reset_hold`: unify register initialization
using new array `exti_romask`
- in `stm32l4x5_exti_set_irq`: rename `n` to `bank`, use new helper
function `regbank_index_by_irq` and new macro `EXTI_MAX_IRQ_PER_BANK`,
explain why there's no `else` clause
- in `stm32l4x5_exti_read`: rename `n` to `bank`, use new helper
function `regbank_index_by_irq`, use `HWADDR_PRIx` formatting in error log
- in `stm32l4x5_exti_write`: rename `n` to `bank`, use new helper
function `regbank_index_by_irq`, use `HWADDR_PRIx` formatting in error log,
unify writes where only bank differs using new helper functions
`valid_mask` and `configurable_mask`
- in `stm32l4x5_exti_init`: use `size_t` instead of `int` in for loop
- in `stm32l4x5_exti-test.c`: instead of declaring intermediate
variables, using `exti_readl` directly in `g_assert_cmpuint`
so that QEMU coding style is respected

Changes from v5 to v6:
- in `stm32l4x5_exti-test.c` : using a helper function
`exti_set_irq()` to help readability
- in `stm32l4x5_exti-test.c` : correct a mistake in test
`test_edge_selector` (adding a necessary NVIC interrupt unpend
so that the assert actually checks something)
- in `stm32l4x5_soc.c` : reducing scope of `i` used in for loops
- in `stm32l4x5_soc.c` : removing useless variable `dev`
- swapping commit 2 (add tests) and commit 3 (connects exti to SoC)
so that the tests pass in the commit they're added

Changes from v4 to v5:
- update the documentation file

Changes from v3 to v4:
- add a test to check that irq trigger selection works correctly
(`test_edge_selector`) and correct `stm32l4x5_exti_set_irq` accordingly

Changes from v2 to v3:
- corrected the license to GPL

Changes from v1 to v2:
- correct the commit messages
- remove a misleading comment

Changes from v3 to v1:
- separating the patch in 3 commits
- justifying in the commit message why we implement a new model instead
of changing the existing stm32f4xx_exti
- changed irq_raise to irq_pulse in register SWIERx write
(in `stm32l4x5_exti_write`) to be consistent with the irq_pulse in
`stm32l4x5_exti_set_irq` (and also both these interrupts are
edge-triggered)
- changed the license to GPL

Changes from v2 to v3:
- adding more tests writing/reading in exti registers
- adding tests checking that interrupt work by reading NVIC registers
- correcting exti_write in SWIER (so it sets an irq only when a bit
goes from '0' to '1')
- correcting exti_set_irq (so it never writes in PR when the relevant
bit in IMR is '0')

Changes from v1 to v2:
- use arrays to deduplicate code and logic
- move internal constant `EXTI_NUM_GPIO_EVENT_IN_LINES` from the header
to the .c file
- Improve copyright headers
- replace `static const` with `#define`
- use the DEFINE_TYPES macro
- fill the `impl` and `valid` field of the exti's `MemoryRegionOps`
- fix invalid test caused by a last minute change

Based-on: 20240108135849.351719-1-ines.varhol@telecom-paris.fr
([PATCH v6 0/2] Add minimal support for the B-L475E-IOT01A board)

Inès Varhol (3):
  hw/misc: Implement STM32L4x5 EXTI
  hw/arm: Connect STM32L4x5 EXTI to STM32L4x5 SoC
  tests/qtest: Add STM32L4x5 EXTI QTest testcase

 docs/system/arm/b-l475e-iot01a.rst |   5 +-
 hw/arm/Kconfig                     |   1 +
 hw/arm/stm32l4x5_soc.c             |  52 ++-
 hw/misc/Kconfig                    |   3 +
 hw/misc/meson.build                |   1 +
 hw/misc/stm32l4x5_exti.c           | 290 ++++++++++++++++
 hw/misc/trace-events               |   5 +
 include/hw/arm/stm32l4x5_soc.h     |   3 +
 include/hw/misc/stm32l4x5_exti.h   |  51 +++
 tests/qtest/meson.build            |   5 +
 tests/qtest/stm32l4x5_exti-test.c  | 524 +++++++++++++++++++++++++++++
 11 files changed, 936 insertions(+), 4 deletions(-)
 create mode 100644 hw/misc/stm32l4x5_exti.c
 create mode 100644 include/hw/misc/stm32l4x5_exti.h
 create mode 100644 tests/qtest/stm32l4x5_exti-test.c

-- 
2.43.0




reply via email to

[Prev in Thread] Current Thread [Next in Thread]