[PATCH v6 32/41] Add mailbox test constants

[Sergey Kambalin]

Signed-off-by: Sergey Kambalin <sergey.kambalin@auriga.com>
---
 tests/qtest/bcm2838-mailbox.c |  1 +
 tests/qtest/bcm2838-mailbox.h | 88 +++++++++++++++++++++++++++++++++++
 2 files changed, 89 insertions(+)

diff --git a/tests/qtest/bcm2838-mailbox.c b/tests/qtest/bcm2838-mailbox.c
index 0928a3dff8..1efd3c628a 100644
--- a/tests/qtest/bcm2838-mailbox.c
+++ b/tests/qtest/bcm2838-mailbox.c
@@ -11,6 +11,7 @@
 #include "hw/registerfields.h"
 #include "libqtest-single.h"
 #include "bcm2838-mailbox.h"
+#include "hw/arm/raspberrypi-fw-defs.h"
 
 REG32(MBOX_EXCHNG_REG,          0)
 FIELD(MBOX_EXCHNG_REG, CHANNEL, 0, 4)
diff --git a/tests/qtest/bcm2838-mailbox.h b/tests/qtest/bcm2838-mailbox.h
index e9e1f53bc9..9222b38bad 100644
--- a/tests/qtest/bcm2838-mailbox.h
+++ b/tests/qtest/bcm2838-mailbox.h
@@ -7,6 +7,94 @@
  * See the COPYING file in the top-level directory.
  */
 
+#define MBOX0_BASE 0xFE00B880
+#define MBOX1_BASE 0xFE00B8A0
+
+#define MBOX_REG_READ   0x00
+#define MBOX_REG_WRITE  0x00
+#define MBOX_REG_PEEK   0x10
+#define MBOX_REG_SENDER 0x14
+#define MBOX_REG_STATUS 0x18
+#define MBOX_REG_CONFIG 0x1C
+
+#define MBOX_READ_EMPTY 0x40000000
+
+#define MBOX_CHANNEL_ID_PROPERTY 8
+
+#define MBOX_PROCESS_REQUEST      0x00000000
+#define MBOX_SUCCESS              0x80000000
+#define MBOX_ERROR_PARSING_BUFFER 0x80000001
+
+#define BOARD_REVISION    0xB03115
+#define FIRMWARE_REVISION 0x548E1
+#define FIRMWARE_VARIANT  0x77777777 /* TODO: Find the real value */
+
+#define ARM_MEMORY_BASE 0x00000000
+#define ARM_MEMORY_SIZE 0x3c000000
+#define VC_MEMORY_BASE  0x3c000000
+#define VC_MEMORY_SIZE  0x04000000
+#define VC_FB_BASE      0x3c100000
+#define VC_FB_SIZE      0x00096000
+
+#define CLOCK_ID_ROOT      0x00000000
+#define CLOCK_ID_EMMC      0x00000001
+#define CLOCK_ID_UART      0x00000002
+#define CLOCK_ID_ARM       0x00000003
+#define CLOCK_ID_CORE      0x00000004
+#define CLOCK_ID_UNDEFINED 0x12345678
+
+#define CLOCK_RATE_EMMC 50000000
+#define CLOCK_RATE_UART 3000000
+#define CLOCK_RATE_CORE 350000000
+#define CLOCK_RATE_ANY  700000000
+
+#define DEVICE_ID_SD_CARD   0x00000000
+#define DEVICE_ID_UART0     0x00000001
+#define DEVICE_ID_UART1     0x00000002
+#define DEVICE_ID_USB HCD   0x00000003
+#define DEVICE_ID_I2C0      0x00000004
+#define DEVICE_ID_I2C1      0x00000005
+#define DEVICE_ID_I2C2      0x00000006
+#define DEVICE_ID_SPI       0x00000007
+#define DEVICE_ID_CCP2TX    0x00000008
+#define DEVICE_ID_UNKNOWN_0 0x00000009
+#define DEVICE_ID_UNKNOWN_1 0x0000000a
+
+#define TEMPERATURE_ID_SOC 0x00000000
+
+#define TEMPERATURE_SOC     25000
+#define TEMPERATURE_SOC_MAX 99000
+
+#define ALIGN_4K 4096
+
+#define PIXEL_ORDER_BGR 0
+#define PIXEL_ORDER_RGB 1
+
+#define ALPHA_MODE_ENABLED  0
+#define ALPHA_MODE_REVERSED 1
+#define ALPHA_MODE_IGNORED  2
+
+#define GPIO_MASK 0x003c
+
+#define GPIO_0 0x00000080
+
+#define GPIO_DIRECTION_IN  0
+#define GPIO_DIRECTION_OUT 1
+
+#define GPIO_TERMINATION_DISABLED 0
+#define GPIO_TERMINATION_ENABLED  1
+
+#define GPIO_TERMINATION_PULLUP_DISABLED 0
+#define GPIO_TERMINATION_PULLUP_ENABLED  1
+
+#define GPIO_POLARITY_LOW  0
+#define GPIO_POLARITY_HIGH 1
+
+#define GPIO_STATE_DOWN 0
+
+/* Used to test stubs that don't perform actual work */
+#define DUMMY_VALUE 0x12345678
+
 typedef struct {
     uint32_t size;
     uint32_t req_resp_code;
-- 
2.34.1