Hi.
-- The daughterboard is the BasicRX Daughterboard.
-- I put the address of my USRP as 192.168.10.1
******************************************************************************************************
soporte@i28:~$ ping 192.168.10.1
PING 192.168.10.1 (192.168.10.1) 56(84) bytes of data.
64 bytes from
192.168.10.1: icmp_seq=1 ttl=64 time=0.051 ms
64 bytes from
192.168.10.1: icmp_seq=2 ttl=64 time=0.051 ms
64 bytes from
192.168.10.1: icmp_seq=3 ttl=64 time=0.049 ms
******************************************************************************************************
soporte@28:~$ uhd_usrp_probe --args type=n200
Error: LookupError: KeyError: No devices found for ----->
Device Address:
type: n200
*******************************************************************************************************
soporte@28:~$ uhd_find_devices
[INFO] [UHD] linux; GNU C++ version 7.5.0; Boost_106501; UHD_3.14.1.1-0-g7c0291ad
--------------------------------------------------
-- UHD Device 0
--------------------------------------------------
Device Address:
serial: 3176CEA
addr: 192.168.10.2
name:
type: usrp2
*******************************************************************************************************
soporte@28:~$ uhd_usrp_probe
[INFO] [UHD] linux; GNU C++ version 7.5.0; Boost_106501; UHD_3.14.1.1-0-g7c0291ad
[INFO] [USRP2] Opening a USRP2/N-Series device...
[INFO] [USRP2] Current recv frame size: 1472 bytes
[INFO] [USRP2] Current send frame size: 1472 bytes
[WARNING] [USRP2] Unable to identify device - assuming USRP2/N-Series device
[WARNING] [UHD] Unable to set the thread priority. Performance may be negatively affected.
Please see the general application notes in the manual for instructions.
EnvironmentError: OSError: error in pthread_setschedparam
_____________________________________________________
/
| Device: USRP2 / N-Series Device
| _____________________________________________________
| /
| | Mboard: N???
| | mac-addr: 00:2c:00:00:00:24
| | ip-addr: 0.0.0.0
| | subnet: 0.0.0.0
| | gateway: 255.255.255.255
| | gpsdo: none
| | serial: 3176CEA
| | FW Version: 12.3
| | FPGA Version: 10.0
| |
| | Time sources: none, external, _external_, mimo
| | Clock sources: internal, external, mimo
| | Sensors: mimo_locked, ref_locked
| | _____________________________________________________
| | /
| | | RX DSP: 0
| | |
| | | Freq range: -50.000 to 50.000 MHz
| | _____________________________________________________
| | /
| | | RX DSP: 1
| | |
| | | Freq range: -50.000 to 50.000 MHz
| | _____________________________________________________
| | /
| | | RX Dboard: A
| | | ID: Basic RX (0x0001)
| | | Serial: 315A5DF
| | | _____________________________________________________
| | | /
| | | | RX Frontend: AB
| | | | Name: BasicRX (AB)
| | | | Antennas:
| | | | Sensors:
| | | | Freq range: -250.000 to 250.000 MHz
| | | | Gain Elements: None
| | | | Bandwidth range: 500000000.0 to 500000000.0 step 0.0 Hz
| | | | Connection Type: IQ
| | | | Uses LO offset: No
| | | _____________________________________________________
| | | /
| | | | RX Frontend: BA
| | | | Name: BasicRX (BA)
| | | | Antennas:
| | | | Sensors:
| | | | Freq range: -250.000 to 250.000 MHz
| | | | Gain Elements: None
| | | | Bandwidth range: 500000000.0 to 500000000.0 step 0.0 Hz
| | | | Connection Type: QI
| | | | Uses LO offset: No
| | | _____________________________________________________
| | | /
| | | | RX Frontend: A
| | | | Name: BasicRX (A)
| | | | Antennas:
| | | | Sensors:
| | | | Freq range: -250.000 to 250.000 MHz
| | | | Gain Elements: None
| | | | Bandwidth range: 250000000.0 to 250000000.0 step 0.0 Hz
| | | | Connection Type: I
| | | | Uses LO offset: No
| | | _____________________________________________________
| | | /
| | | | RX Frontend: B
| | | | Name: BasicRX (B)
| | | | Antennas:
| | | | Sensors:
| | | | Freq range: -250.000 to 250.000 MHz
| | | | Gain Elements: None
| | | | Bandwidth range: 250000000.0 to 250000000.0 step 0.0 Hz
| | | | Connection Type: Q
| | | | Uses LO offset: No
| | | _____________________________________________________
| | | /
| | | | RX Codec: A
| | | | Name: ??????
| | | | Gain Elements: None
| | _____________________________________________________
| | /
| | | TX DSP: 0
| | |
| | | Freq range: -200.000 to 200.000 MHz
| | _____________________________________________________
| | /
| | | TX Dboard: A
| | | _____________________________________________________
| | | /
| | | | TX Frontend: 0
| | | | Name: Unknown (0xffff) - 0
| | | | Antennas:
| | | | Sensors:
| | | | Freq range: 0.000 to 0.000 MHz
| | | | Gain Elements: None
| | | | Bandwidth range: 0.0 to 0.0 step 0.0 Hz
| | | | Connection Type: IQ
| | | | Uses LO offset: No
| | | _____________________________________________________
| | | /
| | | | TX Codec: A
| | | | Name: ad9777
| | | | Gain Elements: None
[WARNING] [UHD] Unable to set the thread priority. Performance may be negatively affected.
Please see the general application notes in the manual for instructions.
EnvironmentError: OSError: error in pthread_setschedparam
[WARNING] [UHD] Unable to set the thread priority. Performance may be negatively affected.
Please see the general application notes in the manual for instructions.
EnvironmentError: OSError: error in pthread_setschedparam
****************************************************************************************************************
I'm not completely sure what is happening. it seems I have an USRP2. I put it wit address 192.168.10.1, but when I run uhd_find_devices is with 192.168.10.2
¿Could be that?
Isaac T.