On Fri, May 8, 2009 at 3:02 PM, <address@hidden> wrote:
Hi all-
I have a USRP2 with a LFRX daughterboard. I'm trying to acquire two
channels each at a separate frequency where Ch0 is amplitude
modulated and Ch1 is not. As per suggestions made to me from this list,
to capture two channels at separate frequencies I was
advised to tune the USRP2 to an average frequency and then use
translating filters to capture the band around each frequency
separately. Typically the AM carrier on Ch0 is at about 1 MHz, and the
signal on Ch1 is about 5 kHz. For both channels I'm
interested in no more than 5 kHz of bandwidth.
I'm using svn 10991 with the SD card updated to the latest fpga and
firmware images on a Fedora 10 x86_64 machine. I don't think I'm
doing this correctly since my spectra is all wrong; perhaps somebody can
help me out. First let me post my USRP1 code that does
this, as this was my starting point:
USRP1: options.decim = 128
usrp_decim=options.decim
self.u = usrp.source_c(0, usrp_decim)
self.u.set_dc_offset_cl_enable(int(0),int(15)) # dc removal off
adc_rate = self.u.adc_rate() # 64 MS/s
# Set the decimation in the FPGA
usrp_rate = adc_rate / usrp_decim # 500 kS/s
#set the decimation in software on the host PC
sw_decim = 10
demod_rate = usrp_rate / sw_decim # 50 kS/s
if not self.u.set_nchannels(nchan): #nchan = 2
sys.stderr.write('set_nchannels(%d) failed\n' % (nchan,))
raise SystemExit
self.subdev = self.u.db(0) + self.u.db(1)
if (len(self.subdev) != 6 or
self.u.db(0,0).dbid() != usrp_dbid.LF_RX):
sys.stderr.write('This code requires a Basic Rx board on Side
A\n')
sys.exit(1)
self.u.set_mux(gru.hexint(0xf0f0f1f0))
# deinterleave two channels from FPGA
self.di = gr.deinterleave(gr.sizeof_gr_complex)
# Channelize the signal of interest.
lpf_coeffs = gr.firdes.low_pass (1, # gain
usrp_rate, # sampling rate
demod_rate/2, # passband cutoff
500, # width of
transition band
gr.firdes.WIN_HANN)
self.lpf_0 = gr.fir_filter_fff (sw_decim,lpf_coeffs)
self.lpf_1 = gr.fir_filter_fff (sw_decim,lpf_coeffs)
# Demodulate with classic sqrt (I*I + Q*Q)
self.magblock_0 = gr.complex_to_mag()
# Get real part of Ch1
self.splitter_1 = gr.complex_to_float()
# now wire it all together
self.connect (self.u, self.di)
# Ch 0
self.connect ((self.di,0), self.magblock_0)
self.connect (self.magblock_0, self.lpf_0)
# Ch 1
self.connect ((self.di,1), self.splitter_1)
self.connect ((self.splitter_1,0),self.lpf_1)
etc
Then I define two set_freq functions, one for each subdevice. Ch0 is
tuned to the carrier frequency of the AM signal, Ch1 is tuned
to 0 Hz.
Now, on the USRP2- since I have only one ddc, I can only tune to one
frequency:
options.decim = 128
freq = 1.e6
self.u = usrp2.source_32fc(options.interface, options.mac_addr)
self.u.set_decim(options.decim)
adc_rate = self.u.adc_rate() # 100 MS/s
#set the decimation in the FPGA
input_rate = self.u.adc_rate() / self.u.decim() # 781.25 kS/s
#set the decimation in software on the host PC
sw_decim = 16
demod_rate = input_rate / sw_decim # 48.828 kS/s
# deinterleave four channels from FPGA
self.di = gr.deinterleave(gr.sizeof_gr_complex)
# Channelize the signal of interest.
lpf_coeffs = gr.firdes.low_pass (1, # gain
input_rate, # sampling rate
demod_rate/2, # passband cutoff
500, # width of transition
band
gr.firdes.WIN_HANN)
self.freq_xlating_lpf_0 = gr.freq_xlating_fir_filter_ccf
(sw_decim,lpf_coeffs, freq/2., input_rate)
self.freq_xlating_lpf_1 = gr.freq_xlating_fir_filter_ccf
(sw_decim,lpf_coeffs, -freq/2., input_rate)
self.magblock_0 = gr.complex_to_mag()
self.splitter_1 = gr.complex_to_float()
# Ch 0
self.connect ((self.di,0),
self.freq_xlating_lpf_0,self.magblock_0,self.gain_correction_0)
# Ch 1
self.connect ((self.di,1), self.freq_xlating_lpf_1,
(self.splitter_1,0),self.gain_correction_1)
etc
I then tune the USRP2 to half of my desired frequency, ie 500 kHz. The
other half of the shifting is down in software.
I would suspect any problem to be in my definition of the
gr.freq_xlating_fir_filter_ccf blocks. I assume the sampling frequency is
set to the sampling rate going in to the filter block before decimation.
I am setting the center frequency to be again at half the
desired frequency to shift by that amount.
Any thoughts?
Thanks much,
eric
_______________________________________________
Discuss-gnuradio mailing list
address@hidden
http://lists.gnu.org/mailman/listinfo/discuss-gnuradio