[Top][All Lists]
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [Discuss-gnuradio] Problems with burn-db-eeprom
From: |
John Stralka |
Subject: |
Re: [Discuss-gnuradio] Problems with burn-db-eeprom |
Date: |
Wed, 15 Aug 2007 11:54:48 -0700 (PDT) |
Matt,
<< First off, reburning the eeprom is the LAST step in several step process to
make an RFX board into a MIMO_A board. >> ... yes, as I mentioned in my post
from 7/30/07, I made the modifications that you provided in a post from 2/7/07,
where you stated:
All RFX boards currently shipping are configured for MIMO_B mode, which
requires a Rev 4 or higher USRP (serial number greater than 500).
If you wish to use it with a USRP with a serial number below 500 you
will need to do the following:
Remove R115 (zero ohms) and place it at R116
Remove R36 (zero ohms) and place it at R34
Put the RFX on a USRP (side A) and run the following:
usrp/host/apps/burn-db-eeprom -f -A -t rfxYYYY_mimo_a
where YYYY is the board you have (i.e. 400, 900, 1200,
1800, or 2400).
<< Secondly, why are you doing this? You have MIMO_B boards which is the
optimal setup. The only reason to make a mimo_a board is if you want to use it
with a very old rev 3 USRP, which you do not have. >> ... I'm trying to create
a comm link between two RFX2400 daughterboards. I noticed that there is a
significant amount of RF leakage between two daughterboards within the same
USRP enclosure. Therefore, I wanted to seperate them into two separate USRP's.
I have an USRP with a Rev 4 PCB (2/17/07, Ser #1263) . The only other USRP
that I have access to has a Rev 3 PCB (1/3/05, Ser #409), which according to
your 2/7/07 post requires the corresponding RFX2400 to be modified for MIMO_A
operation.
Is this correct?
In order to use one of my RFX2400 daughterboards with the Rev 3 USRP I have
successfully done the following:
Remove R115 (zero ohms) and place it at R116
Remove R36 (zero ohms) and place it at R34
Put the RFX on a USRP (side A) and run the following:
usrp/host/apps/burn-db-eeprom -f -A -t rfx2400_mimo_a
I can transmit from the Rev 3 USRP, but I cannot receive on it. It seems to
have a tuning problem.
I would appreciate any help. Thank you.
John
----- Original Message ----
From: Matt Ettus <address@hidden>
To: John Stralka <address@hidden>
Sent: Tuesday, August 14, 2007 12:48:15 PM
Subject: Re: [Discuss-gnuradio] Problems with burn-db-eeprom
John Stralka wrote:
> I reinstalled the trunk version of GNU Radio, and I was able to successfully
> burn the RFX 2400 to MIMO A. The problem I have now is that I cannot seem to
> get the daughterboard to tune on receive in either a Rev 3 USRP or a Rev 4
> USRP. I've verified that it is reporting MIMO A in the USRP Diagnostics
> within GRC, but when I run usrp_fft.py on the MIMO A board, I get "Failed to
> set initial frequency".
>
> I tried putting at MIMO A (side B) and a MIMO B (side A) RFX 2400 in a
> single Rev 4 USRP. Interestingly, I am able to transmit a tone via a MIMO A
> card and receive it in a MIMO B card. But I cannot receive the tone
> transmitted by the MIMO B card on the MIMO A card due to this "Failed to set
> initial frequency" problem. The MIMO B board's tone is fine. This is how I
> was testing them.
> ./usrp_fft.py -R B -d 256 -f 2.4375e9 -g 10 & ./usrp_siggen.py -f
> 2.437550e9 -i 512 --const -T A
>
> When I burned the MIMO A card, I used the following command:
> ./usrp/host/apps/burn-db-eeprom -f -A -t rfx2400_mimo_a
>
> Is there something I should check? I'm at a loss on how to proceed. Any
> suggestions would be appreciated. Thank you.
>
First off, reburning the eeprom is the LAST step in a several step
process to make an RFX board into a MIMO_A board. The rest of the
procedure is shown here:
http://gnuradio.org/trac/wiki/USRPClockingNotes
Secondly, why are you doing this? You have MIMO_B boards which is the
optimal setup. The only reason to make a mimo_a board is if you want to
use it with a very old rev 3 USRP, which you do not have.
Matt
____________________________________________________________________________________
Park yourself in front of a world of choices in alternative vehicles. Visit the
Yahoo! Auto Green Center.
http://autos.yahoo.com/green_center/